25344384403 Kenmore Refrigerator - Instructions

Read the previous instructions given by other responders, they're spot on. But, in short. . .
Remove all food items from the inside of the door.

Remove Phillips head screw holding top hinge cover, remove cover.

Remove top hinge bolts, making sure not to let the door fall.

Lift door off of bottom hinge.

Dig-out broken bearing.

Install new bearing.

Re-assemble door in reverse order.

**Removing the broken bearing piece turned-out to be the most time consuming part of the job. Incredibly easy fix.

I ordered the part from PartSelect using the part number located on the valve itself. The part was delivered in less than 48 hours from the time I entered it. Replacing the valve was easy and went according to the online video instructions provided by PartSelect. The only thing extra was that I had to replace the brass compression fitting on the copper tubing connected to the inlet of the valve. The old one would not seal properly. The compression fitting was about $1.50 at Home Depot. This is my third purchase from PartSelect and I continue to be impressed by them.

I used pliers to get the remaining shelf support studs out, then the new ones just snapped right in place. Very easy repair!

Downloaded a schematic of the ice container. Disassembled the ice container, keeping track of which different type of screws went where. Followed the schematic to ensure proper sequence of blades and spacers. Manually rotated unit prior to installing into the freezer in case of binding. Finished.

took the screw out of the white flange on the top of the door that attaches to the top of the refrigerator. Then removed the cover , and the two screws attached to the refrigerator top. Then lifted off the door removed the bottom plate that is holding the plastic door holder. and replaced the broken part and replaced the bottom plate , set the door back on the hinge and installed the top two screws and the flange cover and the last screw holding the flange cover in place. It actually took longer to type this than the repair

I got the part, hitched it up and it started working right away it fit in easily, and the directions were easy to follow thank you

It was real easy took the lines off one by one put them on the new unit one by one same with the three plugs than tighten new unit back on fridge.

Had to disassemble the entire ice maker bucket. Simple and straightforward, didn't need any pictures or reference materials. Just time consuming.

Removed the door marking the top hinge placement prior to removal. Pulled the door the rest of the way off. There wasn't anything keeping it attached on the bottom right side. Turned the door upright dug out the old broken cam and replaced it with a new one. Thank you for your web-site. It saved us $$$ you have gained two new fans to your web-site. I have shared your link with many. To to anyone who is having a popping noise when you open your door. Do panic. Log on to Part Select .com. It is your only source of sanity.

Thank you

Liz

Remove the old ice maker by loosening the screws and disconnect wire harness , next fit new ice maker in place connect wire harness and place new ice maker in place put screws in and tighten.

The repair was not it. It was the customer service by the ladys that answered the phone. Both of them were the same as to give me a perpaid return shipping label and my money back. It was like being at the return desk at W.M. and not like at some of the on line service I have come to know...

Gene

Followed video on your site. It was very helpful.
Thank you.

No big deal. I took out the glass in the frame, took out the meat drawer, and removed the broken frame, which doesn't take any tools. After removing the frame, I inserted the new frame, which pops in to two clips in the back, and two in the front on each side. I cleaned the glass and put it into the frame. I re-inserted the drawer into the frame. And VOILA!

Unplugged refrigerator from the wall plug. Removed ice tray cover, removed ice container, lossen the two screws on the ice marker holding it to the back of the fridge, dropped the ice marker down and unplugged the electrical connection. Then removed the ice maker.
Took the new ice marker, plugged the electrical connection back into the back of the new ice marker, screwed the two screws back in where the ice marker goes and tighen the screws to told the ice marker in place.
Replaced the ice container, replaced the ice cover.
Plugged the fridge electrical cord back in to the wall socket.
Done.
It started making ice again in about 10 minutes.

Installed a new Defrost Thermostat.