25344359405 Kenmore Refrigerator - Instructions

Unplugged freezer, used digital multimeter to test defrost thermostat, temperature sensor, start/run capacitor and start/run relay for compressor motor. Found ohms values for start/run capacitor to be out of range and carbon traces on relay base where capacitor connects. Replaced capacitor and relay. Plugged freezer in and compressor immediately started running. On mid-range temp setting, empty freezer, temperature alarm light went off in 3 hours. Freezer has been functioning properly since repair was made. My husband is a licensed elevator mechanic with a background in electrical troubleshooting. He tested the components and completed the repairs.

Unplugged refrigerator from the wall plug. Removed ice tray cover, removed ice container, lossen the two screws on the ice marker holding it to the back of the fridge, dropped the ice marker down and unplugged the electrical connection. Then removed the ice maker.
Took the new ice marker, plugged the electrical connection back into the back of the new ice marker, screwed the two screws back in where the ice marker goes and tighen the screws to told the ice marker in place.
Replaced the ice container, replaced the ice cover.
Plugged the fridge electrical cord back in to the wall socket.
Done.
It started making ice again in about 10 minutes.

Installed a new Defrost Thermostat.

the repair was so easy to do. it did take 2 of us to handle the door removal and reinstallation. we watched the video and carefully removed the door and had no trouble at all with the new parts installation. we knew what to expect and successfully fixed the frig! Good Deal!! Easy fix!!

Tested the start relay and capacitor with a multimeter and determined they were both bad (thank you, YouTube!). Ordered both here and they arrived in 4 days. It took me less than 15 minutes to install both; the appliance is working better than ever! The parts were very easy to access and replace.

The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.

If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.

In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.

Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.

Hope this helps someone. :)

No repair needed just replace shelf and drawer

Old valve comes out with 2 screws, water lines removed and reinstalled on new valve just as they came off the old valve. Entire job took less than 10 minutes. Very easy replacement.

Repair was easy. Unplug refrigerator, turn off water to ice maker, remove back panel, disconnect water inlet valve, disconnect water supplies and electrical connections. Cut ends off tubing to modify to new part connections, connect tubing, connect electrical supplies, reinstall back panel, plug refrigerator in, turn water supply back on. We made sure that there was no ice build up in the supply tube into the ice maker and made sure that everything worked correctly before putting it all back together. It was an easy repair.

Followed the online video from this site

Removed old water valve w/ screwdriver, cut threads off old hose (as they just plug straight into new valve) & pushed hoses into new water valve. Solved both problems!!!!

I just removed the filter and then removed the filter housing. The housing is mounted using two screws. The only difficult part was removing the elbows from the water in and out lines. I don't believe the elbows are reusable. So I would go ahead and order new elbows when replacing this part.

I watched the video and followed every step as outlined. It worked perfect, until I reconnected the supply line to my triple water valve. I used the old compression fitting and the compression nut. I should have cut the line and installed a new fitting and nut. The water on the floor the next morning reminded me of that. So back out I went and replaced the compression fitting and it has been as good as new. The ice maker took a few cycles to work again, I think it needed to fill the line with water first. But I have a huge sense of pride every time I hear water dispenced or ice dump in the freezer. Thanks for the help and encouragement!

Remove the food items from the shelves on the door, Phillips screwdriver to take the top cap off. Adjustable wrench to take the two screws off the top hinge. Lift out the door and set aside. Remove two bolts from the lower hinge, reinstall with the new hinge and spacer. Reinstall door on lower hinge. Lift into place to reattach the upper hinge. Put the food back in and you're done.

Removed ice bucket from freezer. Remove ice. Remove 2 phillips head screws from the inside front of ice bucket, and 2 fromt the bottom front to remove the front cover. Remove the E clip and washer from ice crusher shaft. Remove 4, 1/4” head screws from ice crusher housing. Unclip the selector shaft from crusher door paying attention to position.Slide housing off of shaft and discard. Install new housing over shaft and install the 4 screws. Install selector shaft into door. Install the E clip and washer onto shaft. Install front housing with the 4 screws previously removed. Refill bucket with ice and install bucket back into freezing taking care to orient the ice screw shaft into the cog in the back of the freezer as well as the door selection shaft. Test operation.