All Installation Instructions for Kenmore Refrigerator 25331444303

The refrigerator wasn't getting cold the freezer was getting to cold

Followed the installation instruction for both parts now both the freezer and refrigerator are getting cold

Parts Used:

Defrost Thermostat

Defrost Timer - 60Hz 120V

eddie from CHICAGO, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Ice maker stopped producing Ice.

After determining the ice maker was getting water but not harvesting the ice, I ordered a replacement Ice Maker. Installation was easy. One electrical connection and two screws. Following the video to make sure I did not miss any steps I had ice in just a few hours. Just in time for a July heat wave!

Parts Used:

Replacement Ice Maker

Fred from WAPAKONETA, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Ice maker not making Ice

Unscrewed (loosen) screws lifted unit out unplugged electrical connection. plugged in unit hung on screws tightened screws and had ice in less then 1 hour. Rick

Parts Used:

Refrigerator Ice Maker Assembly

Colline from PENDLETON, OR
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

first fresh food too hot, then freezer too hot

Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done!!! Couldn't have been easier.

Parts Used:

Defrost Timer - 60Hz 120V

Rita from Lake Luzerne, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

the refrig was in storage for about a year, the freezer door warped

removed freezer door and installed the new one. This was a pretty easy thing to do, although putting the old handle on the new door was a challenge. No knowing that there is a plastic piece holding the top of the handle i broke the that piece and had to order another one. Mean while the freezer was making alot of frost inside, so that had to be cleaned after the new part came.

Parts Used:

Handle Mounting Block

Jeffery from Phillipsburg, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

the freezer would stick in defrost and not come out

Removed the vent cover at the bottom. Removed the screws. disconected the harnes and put the new timer in. This was a very easy fix. Thank You!

Parts Used:

Defrost Timer - 60Hz 120V

carol from woodland, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

IceMaker would not make Ice

Hardest part of this very easy and simple repair was finding my 1/4 inch nut driver, then I was finished in 5 minutes and now the ice maker is functioning.

Parts Used:

Icemaker Assembly

Copies Plus, from Carson City, NV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

4 of 9 people found this instruction helpful.

Was this instruction helpful to you?

The ice maker quit producing ie

Purchased a new ice maker assembly and installed. Very easy

Parts Used:

Refrigerator Ice Maker Assembly

Tommie from Port Lavaca, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Defrost timer was not working

Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.

Parts Used:

Defrost Timer - 60Hz 120V

Harold from Grants, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

I ept finding clumps of ice in try as though water was spilling over ice maker tray.

I loosened the 2 1/4 inch nuts with a nut driver, disconnected the wire harness, and removed the old unit. to replace, I simply connected the harness and bolted the unit back in. The job took about 10 to 15 minutes and the new unit works better than the old one ever did.

Parts Used:

Replacement Ice Maker

Vernon from Albuquerque, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Needed to replace ice maker which had been making clicking noises as ice got jammed and then stopped working altogether.

Followed the instructions that came with replacement ice maker...was very clear and easy to follow and only took 5 minutes. I also watched the video sent via email with my order confirmation which was very well done and easy to follow. The only information that would have helped would have been a note to wait over-night for the ice maker to make ice as I thought I did something wrong when it wasn't making ice right away....waited until morning and had lots of ice. If I knew how straight forward and easy this was, I would have done it a lot sooner.

Parts Used:

Replacement Ice Maker

Nancy from SOUTH CAIRO, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Water Inlet Valve not sutting off

very easy, 1 screw, 2 tube connectors, hardest part was pulling refer. out of enclosure.

Parts Used:

Water Inlet Valve

David from SHERIDAN, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Ice maker stopped making ice

loosened 2 screws with 1/4 inch nut driver, disconnected electric connection lifted old ice maker out, replaced it with new one hooked up electric plug tightened 2 screws

Parts Used:

Refrigerator Ice Maker Assembly

Robert from POTTSTOWN, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Top door rack Part #: PS735098

Figuring out how to remove the cracked door rack was the most complication I had. Once I figured out how to push it up it was easy to remove and then replace it with the new part by just placing it over the nobs and pushing down. No tools needed, just hands.

Parts Used: