25331439103 Kenmore Refrigerator - Instructions

I rolled the fridge away from the wall, unplugged, and looked for large amounts of dust-didn't see much beyond that which was on condenser coil. The motor was locked up so I removed the three screws and pulled the finger-like connectors. The new kit has a special bracket to mount the smaller frame motor. Getting the two screws into that is challenging w/out a long magnetic screwdriver. Then I added the foam strip & plugged in the new connector. I did not need to but I replaced the two aged capacitors (start,run) from other kits. This will help the compressor to last longer and be more efficient by giving it a boost and sustaining phase difference. Connecting the new "relay start kit" simply required some cutting and splicing with butt connectors of the red and white leads coming from the compressor and covering w/ heat shrink tube

My unit was not defrosting. Defrost heater was not functioning. Defrost heater tested good with a meter. Thermostat (cold) tested bad with a meter. Defrost timer was working properly. I replaced the thermostat but I had to buy red crimp connectors because the blue ones that came with the thermostat are designed for wire bigger than 18 AWG wire. The thermostat leads as well as the wire in my unit were 18 AWG. The crimp was not tight enough for my liking with the blue butt connectors. I also purchased smaller heat shrink tubing. After replacement, the defrost heater started working. I could see it glowing. Unfortunately immediately after getting the heater working the contacts in the defrost timer arced and stuck together thus preventing the timer from exiting defrost mode. The heater went off at this point indicating that the thermostat was now working. I then purchased and replaced the defrost timer and now the fridge is functioning properly. I noticed both replacement parts, even though I looked up my fridge model, were different part numbers than the originals. I'm guessing the new parts are improved? I also noticed the timer was an 8/30 rather than a 10/30 like the original. The fridge is working better than when it was new so evidently defrosting every 8 as opposed to every 10 hours is better for my unit.

Long story short:

Buy the correct crimp/butt connectors before beginning replacement of the thermostat and proactively replace the defrost timer since it is rather inexpensive.

remove food, then the shelf, then use a hot air gun to defrost and loosen the back panel, then remove the panel, then defrost the coil and thermostat area. using wire tools, replaced the defrost thermostat,and re-assembled freezwr and test

I hesitate to say anything since I did exactly what their video told me to do, and it fixed the problem. Couldn't be happier. Was positive I was looking at 1000$ for a new fridge. Love being able to fix it by installing 15$ part myself. Thanks guys.

The freezer was still making ice, but the fridge portion was barely cooler than room temp. I came to the website and saw that the defrost thermostat cured this problem over half the time. I was quite dubious because I don't see how that would affect the non-freezer part of the compartment, but since it was a cheap and easy-looking repair, I figured what the heck, lets see if that's it. Sure enough, it's like new again. I still don't understand it, but I'll take it. The repair itself is simple, just cutting out the old switch and splicing in the new. Two wires, and clip it to the copper tubing where the old one was. The switch is accessed easily after taking out four screws in the back of the freezer compartment. The only hard part was removing the ice-maker, and that's just because the two screws that hold it in are a little hard to get a good grip on. Alas, you have to get the ice-maker out to pull out the back panel, so there's nothing for it but to wheedle those screws out.

The new part fit perfectly! I just snapped it on! Thanks so much Partselect! You processed my order quickly, and I had it in my hands in a few days. What a relief to have this fixed! Thanks again.

Replaced thermo-fuse

Went on line to PartSelect, found and ordered the part. It was here in two days. I removed the old shelf, inserted the new and the frig was as good as new. I was extremely pleased with the ease in identifying the part and the speed of delivery.

The parts arrived next day from Parts Select even though I only had them shipped FedEx Ground and were an exact replacement for the OEM parts. It only took 5 minutes to remove the old parts and replace them with the new ones using a nut runner, lineman dikes, and two wire nuts. I had the repairs completed in 5 minutes but it was actually the compressor that was shot and not the relay and run capactor. End of the day the $60 I spent in parts was cheaper than the $500 quote the local appliance guy gave me and confirmed the same thing...fridge was dead and needed to be replaced. My wife it happy now that we have a new, larger, stainless fridge ;) Thank you Parts Select for quick service and exact fitting parts!

Pryed the old loose catch is on the bottom used a common screw driver.pulled the two wires off reversed the procedeure to put the new switch in.took about 5 minutes.

snapped old one out by hand and installed new one with ease been broken for year could not believe how easy it was

snapped the wires from frig onto the proper prong and viola,it works. The proper prong is identified by the size because there are two prongs with the wires and two connecting prongs in the socket. I talked to a very helpful representative and she gave me the number for Frigidaire, when I was confused by the placement of the wire. Wish I had remembered her name to share with you. As it turned out I didn't need to call Frigidaire.

Not long after we bought this fridge, the plastic on the light switch cracked, making the lever stick out too much so that the door wouldn't close. It's been taped down ever since. I simply pulled the old switch out and plugged the new one in. I'm kicking myself that I didn't do this ages ago. It was so easy and now I can see inside my refrigerator again.

Unplugged frig. removed old switch with the aid of screw driver. removed wires and taped; plugged frig. back in and waited for new one. new one came, unplugged frig.removed tape from wire clips plugged in to switch and pushed switch into socket hole and plugged frig. back in; shut door, works like a new one.

We simply replaced the door rack. It was extremely easy with the quick delivery of the product!