25331420103 Kenmore Refrigerator - Instructions

I watched the videos (they really help) and followed the steps. Everything went smooth with no surprises

jump thermostat,fan and compressor came on, ordered thermo from this excllent parts supplier, part came in 4 days later, it was exact replacement, works exactly right!

Watch the video provided by PartSelect and did exactly the same percedure. Shows what screws to remove and how to remove and replace the part. The freezer compartment was iced up quite a bit so defrosted it before installing part.

Exactly as the video showed, except I had to take the evap coil cover off and use a hair dryer to thaw it out. It was still frosting up too much, so I ordered the thermostat as well. Both were really easy, once i saw the location of the defrost timer and the thermostat. Thanks for the great site, prices that put the big store to shame, and the good video too!

Refrigerator and freezer was not cooling sufficiently due to an inoperative evaporator cooling fan. Replacing the mini evaporator fan was extremely easy. Here are the steps needed to replace the fan. Step 1: Unplug refrigerator/freezer main power cord from the electric wall outlet. Step 2: Remove the food rack from the freezer compartment. Step 3: Using a 1/4" nut driver, remove the (2) 1/4" screws that hold the freezer vent panel/temperature control in place. Step 4: After removing the screws, disconnect the motor's wire harness connector which is located on the top left corner behind the freezer's vent panel/temperature control. Step 5: Pull away the entire vent panel/temperature control panel and lay it flat on a table. Step 6: Remove the vent cover from the main panel by holding the left side and the right side of the vent cover and squeeze both ends at the same time. Step 7: With the motor now being visible pull the motor's fan blade straight off. Step 8: Using the 1/4" nut driver, remove the (2) screws that hold the motor bracket to the rear of the main panel. Step 9: Using the 1/4" nut driver remove the (2) screws that hold the motor to the bracket and the (1) ground wire screw. Step 10: Install new motor back onto the bracket with the original (2) screws and the (1) ground wire screw onto the same locations.Step 11: Re install the (2) screws that mount the fan bracket to the back of the main vent panel.Step 12: Push the motor's original fan blade back on the shaft until it's fully seated. Step 12: Snap back in place the small vent panel back onto the main panel. Step 13: Push in place until you hear a click, the motor's wiring harness connector back onto the top left corner of the freezer's main power wire harness connector. Step 13: Push the main vent panel until it's in place and then reinstall with the original (2) 1/4" screws. Step 14: Reinstall the freezer's food rack back in place. Step 15: Plug in the main power cord into the wall outlet. Get ready to enjoy ice cold drinking water and a super cold freezer. Pete,your weekend mechanic

Initially, I traced the noise down to the evaporator motor area. I thought it was the fan blade so I ordered and changed it. Noise level better but still not good. Then I ivestigated problem area again. Removed the motor,discoverd that the motor shaft was loose /drifting which caused the "hummm" and uneven fan blade rotation. Orderd and installed new motor and all is good.

unplug fridge,Then take rack out n remove the 2 screws on the icemaker set aside,then remove 2 screws on the back panel, cut wires n splice in new part! put back the same.

Checked defrost timer. It was a shocker: it was completely burnt out. Replaced it with the new part very easily. I thought now it would defrost properly but unfortunately the thermostat also was shot. I had ordered it along with the timer just in case. It was not expensive at all and I saved time but having it with me when I replaced the timer. NOW ALL IS WELL AND REFRIGERATOR SECTION COLLING PROPERLY. THANKS TO VIDEO AND PARTSELECT.

per the video..easy installation....unfortunately the temperature did not improve. We still have a refrigerator temp in the upper freezer.....and a "cooler" in the refrigerator section

Followed Internet video instructions for both parts. Two suggestions: Forget the heat shrink tubing and use electrical tape instead, tubing is short in length and difficult to use unless you have a correct heat gun. Secondly, my timer didn't click twice but due to instructions I could determine that the timing was correct in the operation after the first click. This method could be explained as well as when to start it in connection with usage to be the most efficient in temperature and operation.

I watched the video online where it described the troubleshooting tips for this type of symptom. So I knew exactly what the problem was which is the defrost timer. After the part came in I just unscrewed (4 screws) the box which houses the thermostat and the defrost timer from top ceiling of the refrigerator section. Then I just unscrewed and unhooked the old defrost timer and replaced it with the new one. After finishing the installation I turned the fridge on. At first nothing happened. So I turned the dial on the defrost timer with a flathead screw until it clicked and the fridge came alive. I waited for an hour or so. The cooling cycle completed and the fridge stopped as expected. When I opened the door I noticed the interior is much colder than before and right after closing the door the fridge hummed back into life again. So I know my fridge is working again. Thanks to PartSelect for providing the right part for my refrigerator. I will definitely buy from them again if anything goes wrong.

I should have ordered start kit instead of start capacitor. The start cap astir did not fix problem so I ordered kit. Compasator comes as part of kit. Followed enclosed instructions. Cut existing wires and reconnected new wiring. Simple as that. It's a plug in item. Now worried it may be working to good. Freezer down to 10 deg. Watching to see if compressor is running to long. Seems ok lol. Wife hates me now. She wanted new frige.

1. Disconnected electrical. 2. Removed upper console in refrigerator by removing 2 nuts. 3. Disconnected wiring from console. 4. Removed 2 screws from defroster timer part and pulled off from connector. 5. Replaced with new defroster timer and put everything back together. Thank you Steve for the U-Tube step by step video.

After some troubleshooting to ensure the thermostat and heating element were working, determined that the defrost timer was the problem. With the defective part, I was able to manually advance the timer to activate the defrost cycle, but it wouldn't do so on its own. Unplugged the refrigerator from the wall. Timer is located in the refrigerator compartment at the very top. The compartment houses the cooling thermostat, the light bulb and the defrost timer. Using 1/4" nut driver, remove 4 screws holding compartment cover to top of fridge. Lower a bit to access electrical wiring. Wiring harness can be unplugged to work on the timer away from the fridge which makes it a bit easier. Timer is mounted with 2 phillips head screws. Remove screws and unplug timer from wiring. Install new timer, plug in wiring, secure with the phillips head screws and remount entire compartment.

followed the video very esay