Models > 2300ERS > Instructions

2300ERS Jenn-Air Cooktop - Instructions

All Instructions for the 2300ERS
61 - 75 of 180
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Rear burner always high, ignored temperature setting.
Turned off breaker for range. Removed 4 phillips screws on control panel, tipped it forward and rested it on top of partially open oven door. Removed knob and nut on old switch. Moved wires, one at a time from old to new switch. Put new switch in place, tightened nut and pushed on knob. Put control panel back in place and installed 4 screws... piece of cake.
Parts Used:
Surface Unit Infinite Switch Kit
  • Dana from Chapel Hill, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip bowl rusted out
pulled the old one, inserted the new one.
Parts Used:
Chrome Trim Ring - 8 Inch Drip Bowl - Chrome - 8 Inch
  • William from TULSA, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ring adapter was the original and was pretty well worn through.
Removed the old adapter and replaced it with the bright and shiny new one that fit perfectly.
Parts Used:
Chrome Trim Ring - 8 Inch
  • Edward from Brooksville, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip pans were a mess
Replaced the drip pans
Parts Used:
Drip Bowl - Chrome - 8 Inch Drip Bowl - 6 Inch
  • Chhristopher from Houston, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My electric range burner was not heating.
All I had to do was remove the old burner and push the new burner into place. It couldn't have been easier.
Parts Used:
Delta Frame Surface Unit - 8 Inch
  • Joyce from Oceanside, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The radiant ring element had broken
Removed old element, plugged in new one, tested ok
Parts Used:
Delta Frame Surface Unit - 8 Inch
  • Martin from Alexandria, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
stove top burner would not heat
new element plugged into burner connection- an easy fix
Parts Used:
Delta Frame Surface Unit - 6 Inch
  • Marjorie from Indianapolis, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip pans were in need of replacement
No brain surgery required. Removed electric burner, put in new drip pans. Voila! Good for many more years of service looking like new.
Parts Used:
Drip Bowl - Chrome - 8 Inch Drip Bowl - 6 Inch
  • JOANNE from MONKEY ISLAND, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The original grease filter was damaged in our dishwasher (it is quite fragile) and needed to be replaced.
1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover
Parts Used:
Range Grease Filter
  • Martyn from Middletown, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old Stove Top
Ordered new cartridges
Parts Used:
Surface Burner Knob
  • Robert A from Farmington `, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner not wrking well and did not fit well anymore. The whole burner was slippig when cooking withit.
Took out the old element, ring and drip and replaced with new.
Parts Used:
Chrome Trim Ring - 8 Inch Delta Frame Surface Unit - 8 Inch Drip Bowl - Chrome - 8 Inch
  • Veronica from East Sandwich, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner receptacle was broken
The repairs were very simple we just disconnected one screw then removed the old one and replace with new one. The left side took a little longer, because of the 8 screws we needed to remove to take the back panel off. But once we had it taken off the replacement was a snap. Nothing to it.
Parts Used:
Drip Bowl - Chrome - 8 Inch Drip Bowl - 6 Inch Surface Burner Receptacle Kit
  • Molly Grace from Victoria, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Could Not Use One Burner
Turned power to stove off. Removed two screws from cover - lifted cover up and pulled switch out and disconnected wires. Put new switch in and connected wires. Made sure that it was in correct position by placing knob on to make sure off position was correct - then placed plate in position and closed - put two screws back on plate and put new knob on. Turned power back on and turned knob and burner back in operation
Parts Used:
Surface Burner Knob Surface Unit Infinite Switch Kit
  • Anne from Bedford Hills,, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken knob dhaft
Replaced wires from broken to new part.
Parts Used:
Surface Unit Infinite Switch Kit
  • Richard from THE WOODLANDS, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
blower motor was making loud noise
removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.
Parts Used:
Range Motor Isolator
  • alphonso from plainfield, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench set
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 2300ERS
61 - 75 of 180