2300 Cooktop - Instructions

William from TULSA, OK
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Broken knob dhaft

Replaced wires from broken to new part.

Parts Used:

Surface Unit Infinite Switch Kit

Richard from THE WOODLANDS, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Could Not Use One Burner

Turned power to stove off. Removed two screws from cover - lifted cover up and pulled switch out and disconnected wires. Put new switch in and connected wires. Made sure that it was in correct position by placing knob on to make sure off position was correct - then placed plate in position and closed - put two screws back on plate and put new knob on. Turned power back on and turned knob and burner back in operation

Parts Used:

Surface Unit Infinite Switch Kit

Anne from Bedford Hills,, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

blower motor was making loud noise

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

Parts Used:

Range Motor Isolator

alphonso from plainfield, IL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench set

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

burner receptacle was broken

The repairs were very simple we just disconnected one screw then removed the old one and replace with new one. The left side took a little longer, because of the 8 screws we needed to remove to take the back panel off. But once we had it taken off the replacement was a snap. Nothing to it.

Parts Used:

Drip Bowl - 6 Inch

Surface Burner Receptacle Kit

Molly Grace from Victoria, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Burner not wrking well and did not fit well anymore. The whole burner was slippig when cooking withit.

Took out the old element, ring and drip and replaced with new.

Parts Used:

Chrome Trim Ring - 8 Inch

Veronica from East Sandwich, MA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Old Stove Top

Ordered new cartridges

Parts Used:

Robert A from Farmington `, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The radiant ring element had broken

Removed old element, plugged in new one, tested ok

Parts Used:

Martin from Alexandria, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

stove top burner would not heat

new element plugged into burner connection- an easy fix

Parts Used:

Delta Frame Surface Unit - 6 Inch

Marjorie from Indianapolis, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

My electric range burner was not heating.

All I had to do was remove the old burner and push the new burner into place. It couldn't have been easier.

Parts Used:

Joyce from Oceanside, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Adaptor ring and drip bowl corroded over the years and the heating element was acting up.

I removed the old heating element, then the drip pan and then the adaptor ring. I cleaned the residue and buildup that was under the ring and on the surface below, I then snapped in to place the adaptor ring and then oriented and placed the drip bowl in place and finally oriented and pushed the heater element leads into their socket.

I turned the heating dial on and immediately felt the element warming up.

Checked Low temp and then Hi temp.
Everything is working and looking fine. The wife wants to replace the other ones, she says that it's easier than cleaning them.

Parts Used:

Chrome Trim Ring - 8 Inch

John from Portsmouth, NH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

old nkobs old and discolored

took old knobs off replaced in 3 minutes

Parts Used:

WALTER from EL CAJON, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

knobs were getting hard to read.

Pulled old knobs off, pressed new ones on. Probably well under a minute for 6 knobs. Anyone with the IQ of a horseradish could have done it. But what was really great was the help and personality of the agent at the other end of the phone. Shipping was as promised, and the entire experience was delightful!

Parts Used:

Dave from Bloomingburg, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Drip pans were a mess

Replaced the drip pans

Parts Used: