2155188 Roper Ice Maker - Instructions

turned water off to ice maker unpluged fridg while doing repair which was such short time everything was ok removed 3 1/4 hex screws holding ice maker in position while holding ice maker in hand unpluged wiring connection for it removed old ice mold which coating had come off of which was very simple 2 philips screws which are recessed on control unit then gently wiggle assembly apart paying attention to how all the tray parts went together then reinstalling same way as they were remove very simple repair anyone should be able to do

After removing the ice maker, I guessed that the moter could be the problem,bought new part I installed it and held my breath.thankfully that was it.thanks to parts select I saved a lot of money doing it myself.

My ice maker just stopped filling with water one day and after some troubleshooting, I found that a chunk of ice had built up in the tube between the water supply line and freezer. I took the ice maker out (Don't touch the heating element...it really hurts) and defrosted the ice obstruction by injecting hot water into the tube to melt the ice. I used a new plastic syringe you get with an infant over the counter drug and a bucket to catch the water. I noticed the ice cube mold was peeling and decided to replace the mold. The mold is an easy replacement as long as you remember how you took it apart. My mold had some glue or compound stuck to the side that kept me from getting the mold flush against the motor assembly housing so I had to uncrew and scrape that gunk off and reattached. Other than that, there was nothing to it. Now the ice maker is good for another 8 years.

sears wanted $450 to replace ice maker or $400 for refubished. I ordered a $60 motor/control unit from parts select. Remove ice maker, remove motor cover, three screws replace and ice within the hour.

replaced moduale, work just like new.

unpluged the refrigerator, remove three screws holding ice maker in place, disconnected wire clip, removed front of icemaker by relaesing two clips holding it in place. the module and motor assembly are held in place with three screws. put the icemaker together and replaced it in freezer, and pluged the cord back in. the icemaker started making ice in about 15 minutes. very easy fix

Removed the two screws holding the funnel in place...removed the old one and replaced it witht he new tubing...screwed screws back in and the jov was complete. It actually took longer to get it out of the sack than it did to put it together

Simply removed the old and replaced with the new part.

I unscrewed the fill tube screws from the back of the fridge, and pulled the tube out.

Then I put the new tube in, screwed the screws back in and reconnected the waterline.

I ordered the part and just 1 1/2 days later, it arrived! Awesome!

I took the cover off the ice maker motor. Then I simply unscrewed the three screws holding the motor in place (be VERY careful - the hinge mechanism that holds the ice maker on/off bar needs to be gently removed from the motor so the prongs do not break).

Once the motor and ice maker hinge were removed, I simply pushed the new motor on, screwed all three screws back in, put the cover back over the motor, pushed the bar to 'on' and water flowed and ice was made! I turned it to Max so I would have lots of ice in a short amount of time then returned the switch to Normal and I've not had a problem since.

Pulled off plastic cover on motor, removed 3 screws and removed old motor. installed new motor making sure control arm lined up in slot. be sure to disconnect power before doing this job !!!

removed front cover installed gearbox then attached lift arm plugged in frig turned on h2o and now i have plenty of ice ! ordered part on Saturday got part on monday in the mail and had ice by supper what a great place to shop and the service was great and parts made easy to find on the website. thank you very much! I will refer your business to all my friends.

Change motor on icemaker by taking the screw out the bottom ice tray so it will slide out once I remove the I took door off the icemaker it pops off. And follow the instructons for shower

removed icemaker timer/controler replaced with new part.reinstaled it works perfectly

Removed 4 screws, pulled unit out of slots, unpluged control wires plug and removed from fridg. Removed 3 screws that hold the motor module to unit. Then reversed procedure and had the batch of ice cubes one hour and fifteen minutes from the time I started replacement.