207RCX549 Hotpoint Range - Instructions

Avril from Wasilla, AK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

Was this instruction helpful to you?

element heat wouldn vary

slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.

Parts Used:

Range Infinite Heat Switch Kit

Leonard from Winter, WI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

Was this instruction helpful to you?

The instructions on striping the wires was slightly confusing.

I stripped one wire on the first burner. Then I realized that the terminals were the ones that could be left. Finding a replacement terminal has proved to be difficult. Once I realized my mistake I could change the other three burners very easily.

Parts Used:

Tilt Lock Hinge Mounted Surface Burner Kit - 6"

Tilt Lock Hinge Mounted Surface Burner Kit - 8 Inch

Katherine from Berkeley, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set

Was this instruction helpful to you?

rht. front element would not heat properly

I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.

Parts Used:

Range Infinite Heat Switch Kit

Rod from Huron, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

worn out gasket

Used a putty knife and dental pick to remove old gasket remnants and installed new gasket with putty knife and thumb pressure

Parts Used:

Silicone Door Gasket

Jon from Bishop, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins

Was this instruction helpful to you?

Original trim ring did not fit

I had an appliance guy replace a burner(Calrod unit)on my 47 year-old GE range, but he didn't tell me that the original trim ring wouldn't fit. I decided to look up on PartSelect to see if I could get one to fit the new burner, and I did! Fits perfectly......no tools needed.

Parts Used:

Sarah from San Andreas, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Oven bake element burned out.

Replaced old bake element by removing two screws holding it to back of oven. Disconnected old bake element from lead wires by removing two other screws. Installed new bake element by reversing the process. Only issue is that the tabs on the element that connect to the leads are easily bent and you need to use vise-grips to keep from bending them. Otherwise, very easy. Thank you PartSelect.com for stocking this item that I used to repair my 45-year old GE range!

Parts Used:

Bake Element

Marvin from Warren, NJ
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

dirty drip pans and rings in new house i bought

could not find the proper pans and rings in any diy stores, as stove is so old. went on this site and there they were!!!

Parts Used:

patricia from richland, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

I needed new Drip Pans

I purchased a set of drip pans at the store only to find out that they were not for GE Ranges. I got on line and inquired and your representative was very helpful. The repair was easy. After cleaning the stove I removed the old drip pans and installed them one by one. No problem!

Parts Used:

Gloria from San Jose, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Old drip pans rusted out.

Range is 45 yrs old. New drip pans are different shape. This is only place which had them and VERY GOOD price. Delivery was quick, too!

Parts Used:

Joseph from San Antonio, TX
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Needed to replace drip bowls & trim rings for hard to find older range top....

As easy as 1-2-3 !!! :) Lift up burners, place drip bowls down then trim rings, put burners down! Could not be faster or easier! :) I Could NOT find these parts ANYWHERE !!! :) After much aggravation, I was EXTREMELY happy to come across these parts at PartSelect, online! :) Thanks so much for the diagram, you made is sooooooo EASY to find the precise parts that I needed, now I can cook !!! :)

Parts Used:

Viola from Sacramento, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Drip pan replacement

Couldn't find drip pans locally that fit my stove. I came here by chance searching the internet and found the parts I needed and had them in my hands within a day or two!! Not a big parts repair story but excellent service and shipping!! Will buy from again when needed!

Parts Used: