2043399991 Kenmore Upright Vacuum - Instructions

First, we took the pump off and found that it was leaking. Ordered the part on line. The part arrived in four days as scheduled. The small pump was easy to replace with screwdriver and pliars.

Removed water supply hoses and took drain hose out of drain. Unplugged electrical cord. Turned washer over to see and reach pump easily. Flipped clips holding water pump. Moved hose clamps back on inlet and outlet hoses. Wiggled hoses off pump. Placed new pump and flipped clips back in place. Wiggled hoses back onto pump ports and replaced clamps to hold. Turned washer upright and reinstalled. Using channel lock pliers to move hose clamps was the hardest part.

Pull Washer out, Flip to the right on it's side. Pop two Metal retaining clips, squeeze hose clamps with pliers. Remove pump, sand shaft with dremil or 80 grit sand paper. Replace with new pump. Easy! Push washer back and attach hoses and power. Done 15 minute repair

Removed the four screws from the control housing. Disconnect wire to machine housing. Remove the two clips connecting the machine housing to the back. Remove washing machine housing. Pump is located right in front. Disconnect hoses, remove and replace pump, reconnect hoses. Replace the machine housing. This was the hardest part if all trying to reinstall the housing.Once you get the machine housing in place correctly, put everything back together. You just saved about $125 in fifteen minutes.

Removed the two spring clamps from hoses; removed hoses from pump. Removed spring clips holding pump to motor. Had to pry pump off of motor shaft due to rust on shaft end. Sandpapered rust off of shaft and then lubed same with oil and new pump slid easily onto motor shaft. Re-snapped spring clips to hold pump onto motor and then reinstalled hoses and their spring clamps. Whala, end of story, job well done.

1) Disassembled the lid
2) Took the front Panel off (the old water pump was in the bottom left hand corner in plain site).
3) Used flat head screw driver to gentle pry the top and bottom water pump fasterners.
4) Used pliers to remove top hose camp. Note this is where I discovered why everyone says to put the washer on it back. Water came rushing out. Luckily no damage to the motor.
5) Used pliers to remove the bottom hose clamp.
6) Put everything back together Total time <30 minutes.

Unfortunately, the water is still not completely draining. I am now looking at the hoses for obstructions. Any other suggestions?
Thanks

I unplugged the washer, put a towel down, leaned it back and held it up with one hand while undoing the clamps with plyers. Pulled the two clamps off, pulled the pump, put the new pump on, reattached the clamps. Most of this with one hand while the other held the washer at an angle.

plires took off the two hoses , on clip the two snap clips . pulled out the old pump . put the new one in cliped in the snap clips in & hook the hoses back up

It was the first time I ever ordered parts online or even attempted to repair a washer. You all have made finding and ordering the right part very easy. I got the part in 2 days even though I used the cheapest shipping option (5 to 7 days). I turned off the water, removed the water lines so I could lay the washer on its side. No tools were needed to remove the water pump, just two clips held it on. I put the new pump on, hooked up the water and washed a load that night.

I followed the you tube instructions. The hardest part was realigning the washer housing on the lower frame.

Used online instructions from this site

Just removed the old pump with a pair pliers and snapped the new one on. It was a snap

I shut off the water supply hoses and then disconnected them and also disconnected the power supply cord--next I laid the washer on its back being sure to place a block near the water supply valve so the weight of the washer does not rest on the water valve--next I disconnected the inlet and outlet hoses from the pump--next pop off the two retainer clips on the pump and then remove the pump by sliding off of the motor shaft-----to re- assemble just reverse the procedure and you are done--it is a very easy fix.

First of all, it would have been helpful to have two people take the housing off the frame. One to lift and the other to disconnect the hoses that need to come off the pump and the filler.

Second, THANK YOU to another person that posted about prying the pump from the motor and sanding it to accept the new pump. When I couldn't get the pump off the motor due to rust, I thought both the pump and motor were done. But I worked the pump off the motor shaft (I had to break the old pump, but it was toast anyway) and used a wire brush and sandpaper to clean the shaft. When I got the new pump, it slid on like a champ!

I also used the parts list that came with the washer to make sure I got all the parts back together in the right place. Like I said, I took too much apart and didn't pay attention to what I was doing for later reassembly. Even though the parts list that came with the washer is small and not to scale, it helped me put the thing back together.

I got my part when PartSelect promised and I got help here from the website. I will use this company whenever I need an appliance part.

I Removed hose clamps and 2 pump clamps. I took the old pump(had a small hole burned in it) off and replaced it with the new pump. I replaced the 2 pump clamps and the hose clamps and it was ready to go.