20213 - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The oven wouldn't heat because the bake element had burned a hole through the wall of the element tube.
"First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and removed the two wires." from the burned out element. I plugged in the new element, reinstalled the new element and, 10 minutes start to finish, the oven heats again.
So easy even I can do it. !!!
So easy even I can do it. !!!
Parts Used:
-
Richard from Columbus, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
heating coils (burners) were not working
when the new cartridges came in all I did was unplug the old and plug in the new and I had a new stove
Parts Used:
-
Carol from Holbrook, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
6 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Blower Motor Stopped running
Removed the blower assy. Removed the motor. installed the new motor. Reassembled the blower assy. The problem I had was getting the proper clearance for the squirrel cage blower fan to rotate without rubbing on something. I had to make shims for the mounting flanges of the housing to get it to work. Took a lot of head scratching.
Parts Used:
-
Edwin from Bellevue, WA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Pliers, Screw drivers, Socket set
7 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
high blower vibration
blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.
Parts Used:
-
Lawrence from Chandler, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
10 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old stove burners were rusted out and hard to clean
Unplugged old units and plugged in new units. They fit perfectly and it was all so easy. I have been very happy with PartSelect services.
Parts Used:
-
Pamela from Kerrville, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
6 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cartridge was in need of replacement unit
Unplugged unit,cleaned stove and replaced new cartridge.
Parts Used:
-
Marion from Center Point, IA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I had just installed new burner moduels on my stove top but was unable to find a cover for my grill and decided to go on line to look for one. I was thrilled when I located just what I was looking for. I also had a problem with large pots and pans causing a dark grease like stain on the stove top ar
All I had to do was insert the new burner and place the grill cover over the existing grill top. Works like a charm.
Parts Used:
-
Carol from Frisco City, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
6 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced griddle with burner cartridges
First of all the part arrived a day and a half after ordering which we thought was remarkable. We unplugged the griddle unit and plugged in the cartridge with two burners. It is beautiful.
Thanks.
Thanks.
Parts Used:
-
Judith from Andersonville, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
part was just looking old and worn
Really simple just had to remove the old part by simply pulling it out of the socket and then insert the new cartridge. It looks great it was shipped in a matter of days I was surprised to get it so soon.
Parts Used:
-
Geri from El Dorado, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wall vent cap & damper were broken.
Attached spring to damper, placed on existing 5" duct and secured. Used screwdriver to attach vent cover to damper.
Parts Used:
-
Jim from Sulphur, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loose terminal caused block to overheat and break
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
Parts Used:
-
Dana from Black Mountain, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
6 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner would only get super hot. could not control temp.
removed 4 screws holding burner controls. removed wires off old and placed on new burner control. very pleased with quick shippig of part. two days and range was as good as new. excellent company to buy from
Parts Used:
-
Thomas from Exeter, NH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burners not working
-
Wendel from Marietta, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
6 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
cook top burners on old Jenn-Aire finally quit/broke
Being able to find the right cook top on-line and order it without running around trying to find it in stores was great. Was able to replace old electric burners with new ceramic cook top. Nice to update and easy to 'plug' in the module.
Thanks for being there.
Thanks for being there.
Parts Used:
-
Larry from Grand Junction, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Surface of griddle was worn out
This griddle just simple slips into place above the electric elements.
The REAL story is the efficiency with which my order was filled and shipped. I was impressed! There were constant updates on my order and shipping information! Great job!
The REAL story is the efficiency with which my order was filled and shipped. I was impressed! There were constant updates on my order and shipping information! Great job!
Parts Used:
-
Judith from Sour Lake, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!