1985816152 Kenmore Freezer - Instructions

pulled out wash/dry stacked combo unit from cubbyhole (this was the hardest part) . Shutoff both hose supplies, turn off power to unit.disconnect power cord @ coupling. Disconnect both hoses @ machine and drain into pan. Remove old valve assembly,take note of what wires go where and disconnect. Remove filler hose from valve. Install new unit in reverse order but using new hose washers and be carefull not to cross thread the plastic threads and only tighten as much as needed to keep from leaking. Have bought from these people before and they are SUPER. Had the correct part in LESS than 24 hrs. and for a reasonable price !! Sam

Maytag made this easy. The water value was mounted to a plate on the back of the washer removed one screw, pulled the plate from the washer, removed the valve, reconnected the electrical connections and outlet hose, re inserted the plate, attached with screw and tested. 30 minutes tops and I hwve never done this before. Thanks to partsselect and others for recomenning the correct repair. Others had suggestjng the timer device ($180 +) for the parts. OUCH !!!!!

Just as the video described.... Unplugged the machine, turned off the water, both hot and cold. Unhooked the hoses (replaced them at this time since they were over 5 years old). Took out the top screw holding the frame piece and removed from machine. Took off the wires and the output hose. Removed the valve ass'y from the frame piece. Matched new to the original and reassembled in reverse order.

very well . it was very easy 20 min.

very simple to repair, three screws and disconnecting water supply pulling four wires then reverse steps and done, time spent less than 15 minutes.

My husband figured out what the problem was and I looked for the part. It was easy to find on your web-site, and the picture was spot on! I ordered it and had the part in 2 days. The repair took 15 minutes or less, and my washer is as good as new. Thank you PartSelect for being there when we needed. I will recommend this to everyone.

Very easy as the water inlet valve is located on the back of the washer and it was a simple matter of shutting off the water, undoing water hoses, undoing water inlet valve which didn't even need to remove the back side of the washer and connecting the new part, water hoses and turning water back on. The hardest part was tipping the washer, my sits on top of the cold air return, and balancing on a milk crate. Very pleased with being able to do my own repair.

Because the washer was old, 27 years, I actually ordered a new machine but after doing so was able to get the old washer to pump out the water. It had overfilled and spilled water on the floor. The next time I ran the washer using "warm" setting the hot water inlet solenoid failure was evident. I checked voltage at the solenoid and it was getting power so figured I'd try ordering a $30 part. In a couple of days it showed up and after less than :30 minutes I had the washer running again. It would have taken less time but a screw stripped out and I had to locate a replacement. I'd definitely recommend PartSelect. Oh, we cancelled the replacement washer and figured the Maytag repairman could resume his slumber!

Removed two screws , two more on the valve, loosened the hose clamp. Reassembled the same way

Pulled the washer away from wall and tipped forward, leaning against a chair. Removed the hot and cold water hoses. Removed 1 screw. Pulled the plate off the back of the washer. Removed two screws holding the old valve onto that plate. Took 4 wires off the original valve one at a time and placed the wires one at a time on the new valve, so I didnt have to write down or remember which wire went where. Slid one hose clamp up, pushed the hose off the old valve and placed it on the new valve. Threw the two screws back on the valve and fastened it to the plate. Put the plate back on the back side of the washer with one screw. Put some teflon tape on the threads of the new water valve and screwed on the hot and cold water hoses.

Ordered replacement water inlet valve, switched out within 10 mins and problem solved for less than $50. Maytag design easily allowed for the inlet valve unit to be replaced without accessing interior workings of the washer. The unit is mounted with 3 screws on a removable rear panel where the hot and cold H2O hoses are connected. Very easy! Tested immediately upon completion and was delighted to see that hot, warm and cold water filled the tub extremely fast, the way it worked when purchased new 18 years ago. The web site repair video was key to my success.

My nephew followed directions in the repair video. Washer no longer leaks when warm water is specified.

Studied, diagnosed the issue, looked at symptoms described in ParrtSelect's on line resources, purchased the part. Had it in one day without the need for extra FedEx shipping charges; waspleasantly surprised to see how easy this repair was to make. I then replaced inlet hoses with new stainless steel types. This workhorse pair of of Maytag appliances, constructed in January 1985 will continue to serve for many more years. These are well-built battleships! And PartSelect will be my part source of choice to keep them going!

I didn't expect a problem, but watched the video anyway, it was right on the money. Make sure to use a new clamp for the hose.

With the help of my 3 year old grandson, we removed the inlet hoses and inlet panel. The water inlet valve replacement was a perfect fit. All connections conformed to the original part. I had reviewed a video at the time of order, so was familiar with the process by the time the part arrived. The website was very helpful in determination of what was needed to fix the washer problem. Shipping was fast and tracking the package provided my schedule. I will utilize this site in the future.