Models > 19585 > Instructions

19585 (1988) Kenmore Dishwasher - Instructions

All Instructions for the 19585
76 - 90 of 112
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
We needed a new bottom dishrack the old one was very rusty
I ordered a new rack, snapped the stuff together, and slid the old one out and the new one in. Fit beautifully. Piece of cake and much cheaper than a new dishwasher.
Parts Used:
Lower Dishrack Kit
  • Katherine from Coos Bay, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
3 of 8 wheels had broken off bottom rack.
Piece of cake. Unsnapped the old parts, studied the new ones for a minute to orient myself, and snapped them on. Not quite as simple a twist as the old ones took, but no problem once they were lined up properly. Total time, about 5 minutes or less.
Parts Used:
Tandem Rack Rollers - Set of 4
  • Mederick from Gorham, ME
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
wheels broke on lower tray
pulled old wheel housing off and replaced with new replacements ones. Straightforward task.
Parts Used:
Tandem Rack Rollers - Set of 4
  • RICHARD from JERSEY SHORE, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
end loop on each end of spring broke off
Looked at right side of dishwasher to see how it was attached and did the same. Spring was slightly shorter than the original and the loops are not a sturdy. Will see how long it last.
Parts Used:
Dishwasher Door Spring Assembly w/Adjusting Hook
  • Eieen from Methuen, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Latch had broken on detergent dispenser cover
Remove retainer that holds door color slide in front of door & then remove the slide. Remove cardboard backing, remove electric latch release, remove latch & replace with new one. Open door & slide out the cup dispenser cover pin & spring & replace with new ones. This was all straight-forward & simple.
Parts Used:
Detergent Dispenser Cover Kit
  • Phillip D from Auburn, AL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
8 of 26 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Installed wheel assemblies to rack
Assemblies snap on, no tools needed
Parts Used:
Lower Dishrack Kit
  • Philip from Greene, ME
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
6 wheels missing
easy - removed old wheel holders & pushed new

ones in place. parts came in two days !!!!
Parts Used:
Tandem Rack Rollers - Set of 4
  • Tom from Wappingers Falls, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
soap door hinge broke
I took the pin and i slide it through the first hole attached the spring then sldie it through the second hole and snap the cover on
Parts Used:
Detergent Dispenser Cover Kit
  • Michael from Las Vegas, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
4 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The previous rod holding the cup in place broke
Remove completely the old one and installed the new entire kit.
Parts Used:
Detergent Dispenser Cover Kit
  • Nicole from Newnan, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
was just missing the door and spring
You slide the pin that holds the door in the first hole. then you slide the spring in next. The you slide the pin through the last hole. After that you gently push the door onto the pin till it snaps into place. And your done.
Parts Used:
Detergent Dispenser Cover Kit
  • craig from Columbia, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
4 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Super Fast Shipping
The part arrived the next day with regular postage, outstanding service.
Parts Used:
Upper Spray Arm Tower
  • Karolyn from Wellington, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
7 of 64 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
missing part
screw it in then hook up the hose.
Parts Used:
Drain Check Valve with O-Ring
  • Ruby from Saint Marys, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Unfortunately, a mouse had made its home on top of our surround insulation. For hygienic reasons, I replaced the surround.
1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.
Parts Used:
Tub Sound Shield - Insulation
  • John from Taylor, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
spring on dispenser broken
Removed cover and broken spring ,installed new spring and cover.Did it all in less than 10 minutes
Parts Used:
Detergent Dispenser Cover Kit
  • Delano from Durham, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken door spring
Very easy. Slide the dishwasher out a few inches, install spring per the good instructions, and slide the dishwasher back. Service was amazing. Part arrived just over 24 hours after I made the on-line order. I will use Part Select for all my future appliance parts needs.
Parts Used:
Dishwasher Door Spring Assembly w/Adjusting Hook
  • Jonathan from Newton, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 19585
76 - 90 of 112
Back to Top