177047A Frigidaire Refrigerator - Instructions

First unplug it and pull away from wall to gain access to the Rear of freezer.
From the rear of the freezer. You can clearly see the compressor.....I had to lay in the floor. Best way to see what your doing .
Attached to the side of the compressor
Is square cover over the start relay..it has a metal bail that retains the cover. Simply remove the strap with a flat blade screwdriver the cover can then be removed. A flashlight and screwdriver is all I needed
The switch body plugs onto the compressor with pins or blades. Mine broke in a few pieces by the time it was completely removed. The start switch has very tight connections so its a bit of a struggle to get it off. ..stick screw driver behind it and try pry evenly until its off..secure new switch on the pins and push it in ..there is one single wire attached to the start switch no confusion there.install cover and its retainer and its done..

I replaced the shelf end caps in the shelves of my fridge and I also replaced the gasket around the door.

Every time I would open the door, things would fall out because the shelves were giving, because the end caps were broken. Once I got the new ones, I was amazed that these parts are still available and that they lock right in with no problem. Once you get one in, you then have to place one end of that retaining bar into that, very tightly, making sure the end is completely secure in the cap. Then you can lock the other cap to the other end, lock it into place in the door and whala! It is just that simple.


Now the gaket is another story, it is best to soak the gasket in hot water first to draw it up abit so it will be snug and also to use lubricant such as petroleum around the inside where it is going to fit to the door. This made it extremely easy to afix to my door with no problems. I am so glad for this site.. hundreds of dollars saved!!

Dear Part-select,
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 part if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work


Tom Houck
Spokane, WA
Houck Photo
509-723-3418
tomhouck1@comcast.net

Replaced defrost timer & thermostat.

I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.

Refrigerator started frosting up and running all the time.I'd defrost it and it would frost up again in about a week.The timer seems to be work so I just guest it mite be the Defrost Thermostat.I removed the duck in the center and back panel in the freezer compartment defrosted it and switched Thermostats and replaced panel and duck, going to lower compartment of the refrigerator.So far it seems to be working a little more time while tell.

Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.

Ordered a new defroster timer and replace old one. It works just fine. A $35 repair vs a $500 new appliance.
Cool.
GWE

We have a wonderful Kelvinator refrigerator. It has served us tirelessly for more than 15 years - and looks as good as new! (We frequently clean it out and clean the interior and exterior, to keep it looking and smelling clean)

Replacement of the end caps and shelf was very easy!

The broken end caps were removed (missing for years), and it became one of those small projects that one never gets around to. I finally took down the model number and looked online for it. Google or Yahoo (can't remember which) pointed us to you site. I was SHOCKED to see that the parts were still available! I called your friendly customer order line and had a very pleasant experience placing the order. The BIGGEST shock came when the parts arrived THE NEXT DAY!! Just in time for Thanksgiving! You are AWESOME!

The Repair:

Easy as pie. The end caps simply snap into place. I did the left side first, then carefully inserted the metal bar, which is supported by the two end caps. Next I snapped in the right side cap - DONE. It took longer to clean the bar up, than it did to replace the caps!

The Results:

The bottom door shelf is now useable again. We can place 2 liter beverages and juice containers on the door, where they belong! My wife cheered and commented, "The refrigerator is no longer an eye sore when I open it!" :-)

Thank you Parts Select!!!!

First I removed the broken end caps. I placed the new end cap onto the shelf bar and snapped the end cap into the holding slot on the door interior. Took about 5 minutes. Very easy.

replaced it

I removed the broken end caps by hand. They snap in to the center retainer bar. I ordered replacement parts from part select on their website. New end caps arrived in a couple of days. I installed new caps. No tools needed. Great service by part select. Thank you tm staten island ny

The new parts just popped right into the holes and the door now has two shelves again.

Removed front low grill, removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. Reversed process to install new timer.

I put the end caps on the cross bar and reinstalled it in the fridge. Easy job.