All Installation Instructions for Magic Chef Range 15GA-10

contacts had gotten burnt out/blackened with age so burner was intermittent.

lifted the cover, unscrewed the ceramic wire fastners, put the new part in, and voila, job done and working perfectly

Parts Used:

Range Surface Burner Plug-In Block Kit

john from reading, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Wire broken off plug in block

Removed old block , cut off wires , used new wire nuts, heat shrink , supplied with parts , job done lowered range top went fishing ...

Parts Used:

Range Surface Burner Plug-In Block Kit

Robert from Phillipsburg, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

surface element burnout

The repair was just a matter of sliding the old one out and plugging the new one in. The ease of use of this website was wonderful. Super fast shipment. Im very pleased.

Parts Used:

Economy Y-frame Surface Unit - 8"

david from wellsboro, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Bowl -Drip and gasket

it was relay easy when you get the right pats .so
Thanks for .
PART Select.
Best regard .
Walid

Parts Used:

Chrome Drip Bowl - 8 inch

Drip Bowl - 6 Inch

Walid from Worcester, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Burner Would Not Heat

One screw taken out, 2 wires switched, new part & screw put in. Burner like new!

Parts Used:

Range Surface Burner Plug-In Block Kit

David from Toledo, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Wire broken going to one electric plug for burner

Replace the connector and bracket, spliced the wires, put heat to the schrink wrap and I was done.

Parts Used:

Range Surface Burner Plug-In Block Kit

John from Shelby Township, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

no heat from burner

I raised the stove top, read the instructions to my son while he did the work, then I lowered the stove top, installed the burner, and it worked like magic.

Parts Used:

Range Surface Burner Plug-In Block Kit

George from ST. Charles, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

replace burner coil connector

Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be sure and disconnect power before starting!!

Parts Used:

Range Surface Burner Plug-In Block Kit

dicky from mcrae, AR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Old surface element burned out.

I ordered and received the replacement element, then unplugged the old one and plugged in the new one.

Job done.

Parts Used:

Economy Y-frame Surface Unit - 8"

Royce from Rio Rancho, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

large burners not working

Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so you have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.

Parts Used:

Range Surface Burner Plug-In Block Kit