1500PRA Magic Chef Range - Instructions

Robert from Wilton, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

one pole of the socket corroded to nothing

Starting by me making a substitute prong to keep the stove working while the part this coming by mail. was a piece of cake.

Parts Used:

martien from williamstown, MA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

drip pan were burnt out

simply remove the burner take out the drip pan and bowl individually. Install the new one and replace the burner. no tool was used.

Parts Used:

Delroy from Miramar, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Porcelan Electric Burner Plug broke

The video on your website showed me how to take out 1 screw, cut the existing wires and strip the ends. The kit came with 2 porcelan wire nuts to re-connect the wires and it was done. Less than 10 minutes. It saved me $100.00 to get it repaired.I bought 2 in case I need another one in the future.They only cost $11.00 each. Awesome website.

Parts Used:

John J from Coatesville, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Drip bowls were all rusted.

Removed old rusted drip bowls and put in the new ones. Very easy to do and needed no tools. It made my 25 plus Jenn Air look new again!

Parts Used:

Robin from Seneca, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

old drip bowl was worn out

new drip bowl fit perfectly and was a snap to install.

Parts Used:

Richard from Germantown, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

the old bowls were burned.

really easy.

Parts Used:

Rosibel from Houston, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

unable to remove screw with screwdriver

used drill to remove old screw

Parts Used:

Emmett from Rayville, LA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

heating coils would not work

Remove heat coils, take body of coil inserts out, remove screws from body, cut old receptacle out, tie new recptacle wires to the old piece of left over wires using wire nuts, and reassemble body, insert heating coils and test.

Parts Used:

Adam from Kempner, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Burner did not heat

New receptacle element. I am a girl and I did it.!!!!

Parts Used:

lula from Antelope, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

surface burner stopped working. Was not heating up.

The repair only took me 10 minutes to do. I purchased the surface replacement kit from partselect.com. The part arrived in two days. The instructions were very simple. I read the instructions on line during my purchase. When I received the new part, I simply did the repair. Including shipping, the cost was less than $20.00. A service call would have been at least 5x the cost. Thank you for being there Partselect. (Tim from south bend indiana)

Parts Used:

timothy from south bend, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Cartridge wire burned out

I was unable to remove the screw which held the electrical element.. so I took the new surface burner receptacle and removed the metal part, and used the old one and put in the new one in the old metal part and rewired, and it is like new.. now I need to do another one.

Parts Used:

Robert from San Francisco, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set

Was this instruction helpful to you?

Burner element stopped working

The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not a pretty picture, but that's how repair work is on old stuff.

Parts Used: