119908821 Kenmore - Instructions

I raised the stove top, read the instructions to my son while he did the work, then I lowered the stove top, installed the burner, and it worked like magic.

Removed old block , cut off wires , used new wire nuts, heat shrink , supplied with parts , job done lowered range top went fishing ...

I had bought the 1st set of plug-in blocks at lowes, They were the only type they had the univeral ones! They did not hold the elements plug tight enough and half the time they would have to be punshed in more then they would snap and sizzle- I ordere the newer style and they have done great they are better made and heavier metal parts- they elements fit in snuggly and do not sizzle or nor do I have to push the element in. This stove is 35 years old and I have replaced most everything on it. But it's still cooking...

Instructions included with terminal block assembly. Toughest part was to strip the insulator off of the old wires on the stove. I was originally going to just purchase one but after looking at the other terminal blocks and seeing the burnt insulation and some of the wire strands, I just replaced all 4. PartSelect customer sevice was very helpful to confirm the correct part number I needed for my stove.

Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so you have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.

Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be sure and disconnect power before starting!!

prepared the parts as directions displayed, removed the heating coils and popped the hood on the range, simple curcit 2 wires in to the main harness for each coil. snip, plug and twist add heat wrap to seal the new conections and done very simple fix saved me buying another oven....for now

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Very simply following the online video instructions.

I shut off the breaker checked for power then cut old plugs making sure to allow a little slack. Tightened down wire nuts put on a couple wraps of electrical tape and that was it. Burners work great now I would reccomend this product to anyone with a similar problem.

First I read other comments here; then checked youtube.com to see if there was a video - there was! Easily removed the stove door and the storage drawer to access the spring. Removed the spring and used screwdriver to remove 2 of 3 screws - third had a nut on back which required removal of the decorative panel next to the door. After applying Liquid Wrench, was able to use vise-grip to remove last bolt. Inserted new hinge, attached the spring to hinge and stove frame then inserted the 3 screws. Reattached the decorative panel and was done. Repklaced a hinge, not a stove!!!

First I want to thank Part Select for having the video online or I would not have attempted the repair. Also I saved over $75 on the parts!!!!!! It would have cost me $105 for parts and $125 for service tech to replace the burned off terminal blocks with new ones. Parts cost me $35 with shippiing, I did the repair saving me $195 !!!!!!!!! I replaced the parts as describied in the video and all is well. By the way, I got the parts in less than 24hours after ordering, cheaper than driving 30 miles to pick up overpriced parts !!!!

I removed the burner element, then the drip pan. I took off the old block. Then I had to strip the old wires. Then I put on the heat sleeve, then attached the new wires to the old wires with nuts. Put heat sleeve over this and heated with lighter. Then put everything back together.

I removed the entire burner assembly to avoid having to turn things off at the breaker - the whole assembly can be removed completely from the stove I had. Once it was out and disassembled, the toughest part was putting the new wires into the new block correctly. Once that was done, I had to select the right mounting bracket - there were 2 in the kit. Easy, just attention to detail. The rest of the instructions were easy to follow, re-doing the wires. The re-assembly was trivial, and it worked first time!

After carefully inspecting existing burner receptacles, I unscrewed them, raised and propped stove top. Determined which bracket to use from new kit and proceeded to cut and strip wires, twist ends together with supplied ceramic caps and heated shrink wrap on that junction. Works great. BTW got parts in 2 days in great shape and good directions.