110C65132410 Kenmore Dryer - Instructions

I highly recommend using a multi-meter to test for continuity on the thermistors and the heating element. It will likely save you a lot of time and you can replace the correct part the first time. I found the high limit thermostat to be open. Also note that if you find the same part open, it is most always caused by another part failure or the dryer vent to be clogged up with lint. I also cleaned out the lint chamber which was in pretty bad shape and likely caused my failure. But, the parts were not expensive and were replaced while I was doing the trouble shooting. The video is excellent and if followed all will turn out ok. This is my third different appliance repair, and the parts are always in stock, the standard shipping was 7 days, and everything you need is provided.

Disassembled dryer, removed tumbler, replaced drum support rollers

first i removed the back cover by removing the six 1/4 inch screws then i removed the wires to the thermal switch there were three of them and using an ohm meter i checked each one for continuity until i found the one that had an open circuit. i removed the two 1/4 inch screws holding it in place and replaced it with the new one.

removed the back housing of the dryer and located the thermal switch. unscrewed the old one, popped in the new one and whala! I was back in business!

put the back cover back on the dryer and pushed it back into place.

lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job

Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working

I followed disassembly directions found on youtube and replaced th two-piece ring bearing that was identified by a parts diagra fron PartSelect. The repair was easy. Fix time was about thirty mionutes.

unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mounted new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).

after i got the replacement filter, it fit perfectly. the filter is white & my dryer is beige but i don't care...i'm just happy i have a good lint filter again, for my at least 30 year old dryer....thanks part select!

put the high limit in , plus the temperature , plus the exhaust switches

Thank goodness the part was still available for a 25 year old dryer. Website was great to help solve the problem and the video was wonderful to show me how to identify the part and how to get to it. You take off the back of the dryer and then unscrew the thermostat from it's mooring. Undo the 4 wire connections. Stick in the new thermostat and re-install. Thank you!

I watched the part select you tube video that links specific loud dryer noises to specific broken or loose parts. It allowed me to identify the part I needed, which I ordered through their website. Two days later, I had the part and installed it, with help from another online video that showed me how to take the dryer apart to install the drum support roller. Thank you, the information provided made the repair quite easy. It works perfectly now!

Attributed excessive noise to age of dryer, upon closer inspection, a dish towel had become caught at rear of drum because the drum support rollers were damaged causing the drum to create a space in the rear of the drum. This was large enough for the dish towel to be caught. Originally I thought that the thermal fuse had blown the circuit-which should occur in an overheating situation-however the loose drum had worn through the electrical wire leading to the door switch because it was not properly seated on the rear drum rollers. the wire was repaired with a wire nut, rear drum rollers were installed and it is working again. thank you for the extremely fast shipping

Took of the btm pan and the top to be able to remove the front. Raised the drum enough to replace the right hand wheel. ( the old ones had already been removed) Replace the left hand wheel and bracket. Re assemble the machine. Worst part was trying to do all this with the can of beer in one hand!!

Unplugged the unit, removed the back panel of the dryer and then removed the thermostat panel. Disconnected the wires on the thermostat and changed out the thermostat.