110C65132410 Kenmore Dryer - Instructions

Pulled the dryer out from the wall and laid it on its front on a blanket.Removed the back panel.Disconected the two switches and replaced them with the new ones.Cleaned up dryer replaced back panel and returmed the dryer to its original place and she works just fine.

just like the guy in the video. It was easy to folow his instructions, and the best thing of all i could stop the video if I had a question and then resume!

Received the new lint removal from the box and install it easily

Purchased new heating element and replaced. This was the number one recommendation for the fix for my problem. I do not have any measurement devices to check any of the parts. This was trial and elimination. The old element was badly burnt. Still no heat. The second recomendation was the thermal fuse. I purchased that and replaced. Still no heat. After reading through some of the repair forums on this site I decided to try one more time and replace the thermal cut off kit. A little harder to do because it required cutting and replacing some wire ends. That was the problem. We now have heat and once again I have a happy wife! I left the new element and the fuse in. The dryer heats much faster than it did.
The repair videos on this site were very helpful. Some of the wire changes on the Thermal Cut-off Kit can be very confusing.

Pulled back off dryer as in video and followed directions. One part in the kit was not necessary. Just replaced the fuse and put it all together again and Voila! Dryer works again.

Removed back cover. Removed old timer and connected wiring to the new one. Installed new timer and put the back cover back on.

Removed old filter, replaced with new.

Used the trouble shooting tips provided as a guide and a multimeter to test and find the defective part. Testing indicated no continuity thru the high limit thermostat. I ordered the part and received it in 3 days. Had the repair done a full week before the repairman could even come to the house and saved well over $100 in repair costs and 2 weeks or longer of down time. Great website and service.

Remove backpanel, ohms cut off thermostat, no good, disconnet two wires from defective part and installed a new one.

I follow the instructions from the video you guys show the only issue is putting back the tensioner in place but my brother leaves next door and help me.

I removed all the screws to the back panel to gain access to the inside. checked all thermostats and fuses for conductivity (0.001 ohms) resistance. noticed the thermal cut off fuse (thermostat) was showing no conductivity (infinite ohms or OL). FYI the thermal cut-off kit I purchased included both the thermal cut-off fuse(why this is called fuse is a lie its actually a thermostat) and high limit thermostat. I'm seeing alot of users purchasing these seperate but it isn't neccessary. You might need some wire strippers with a crimper though to install everything.

It went well, I followed the instruction video and referred back to it if any questions or difficulty. The instructor on the video was obviously very experienced and duplicating his actions exactly was very helpful, One thing I noticed that wasn't mentioned was that the thread on the wheel / motor is left handed.

Watched the videos available. Opened the top and saw tub jumping. Unplugged and removed front panel. Saw tub rollers were broken or melted. Removed tub watched more videos, and installed the felt belt I got from PartsSelect. Trouble removing the tub rollers, but finally got them off. The axles had a sticky residue which I removed with 220 grit sandpaper. I installed new rollers I had bought locally. Reassembled dryer. Worked quietly and smoothly, and it no longer shut itself down. Worked well for one day when it started.s loud noise with bumping. I found both rollers had lost their outer rim , and the tub was running on hard plastic and there was sticky residue back on the ankles. I stopped there.

Followed the video - easy!

Turn off Gas, unplug electric cord, remove rear cover, remove two screws holding the lint trap to the top, raise top flip[ping to the back supporting it not to damage wiring, remove bottom front cover, remove door springs, remove front cover, disengage belt tensioner, remove drum. unclip right side roller and remove, unbolt left wheel mount from the rear and the bracket in the front, remove clips or cut off (new ones come with new clips). clean the wheel shafts, light sanding if needed, apply light coat of lithium grease. replace wheels and reassemble dryer in the reverse order from disassemble. roll drum by hand after front back on to ensure it rolls without catching. Finish and test.