11089722990 Kenmore Dryer - Instructions

Popped out the old lent trap & popped in the new one..and walla perfect repair..

I followed the YouTube video. Took the back panel off, took the lint thing off and proceeded as indicated in the video excerpt I didn't take the top off.

It was very easy to install the new parts successfully thanku parts select I will always keep using your business the representative was so helpful and understanding my problem I wish I could remember his name he was outstanding and a 100 thumbs up to him

I follow the instructions from the video you guys show the only issue is putting back the tensioner in place but my brother leaves next door and help me.

I watched a U Tube video about banging sound from dryer. Once I recognized the problem, lifted the top, removed 2 screws holding the front, removed the drum, and bingo. Saw the worn out drum roller. Ordered the replacement parts from "PartSelect" on line (Great Company). Was in no hurry, so I chose regular mail delivery. 4 days later, got the correct replacement parts, put the dryer back together, and now, the dryer is quieter then when I bought it new, a thousand years ago. I will never again be afraid to tackle an appliance issue. THANK YOU !!!

First and foremost turn power off to dryer at main box. Next remove screws say lint filter, then gently pry right and left front corners up with putty knife. Raise top and secure. Disconnect switch wire by using flathead sliding in between connection. Next remove 2 screws under front opening to dislodge switch. Repeat process in reverse order...takes 30 min. tops...

I remove the lint trap and the two screws that held the top down. Next to unscrew the two screws that holds the door switch. I prized the top up with a screwdriver . I unplugged the door switch and plugged in the new one. I inserted the switch into the door and replace the screws. I snapped the top back into place and replace the screws in the lint trap. I close the door and turn the dryer on and it worked. I followed the directions you provided on line. They were very easy to follow.

First unplug unit to avoid shock. Using a flap blade screwdriver lift the front corners of the top. Unplug the switch located on the right side in the front. Remove two screws holding the switch in place. Remove old switch and reverse to install new switch. Entire project took less than 10 minutes. Oh yes the wife was so happy she made me a dish of fudge brownies. :)

Hi, I am a working mom, and my dryer quit just after it had been behaving strangely. At first, it kept spinning after the door was opened. It eventually stopped working, and I assumed that the door switch must be the culprit. I purchased the part from the catalogue, and watched the installation video. Repair: After unplugging the dryer and removing the lint screen, I used a philips head screwdriver to loosen and remove the two screws located at the lint trap. I then inserted a flat screwdriver into the area between the top of the dryer casing and the face. Per the video, at approx. 2 inches in from the left and right side. I did this while gently applying pressure from the back of the dryer top to the front. This loosens the clips allowing the top to be lifted back and out of the way. I then opened the dryer door and commenced loosening and removing the two screws that hold the dryer switch in place. I used my screwdriver to gently separate the wiring harness connection, as it also has a clip to keep the connection tight. With these items free, I simply popped the little black thingy back through the hole (The black thingy just keeps the slack in the wiring from sagging, I think). With the old part removed, I then installed the new part accordingly. I reversed my way back out of the process respectively. I plugged her back in, and turned her on. Back in business.

The numbers on the metal plates were the JC Penney numbers - that no one recognizes. I eventually found the model number inside the timer case on a printed schematic. I started by disassembling whatever metal covers were removable by finding sheet metal screws and unscrewing them. If you pull on the sheet metal covers, you can find where they are connected to the frame. Eventually, I found that both the heating element was broken and the thermostat was fried. It took a while looking at various websites to find the proper parts. It's all OK now.

just like the guy in the video. It was easy to folow his instructions, and the best thing of all i could stop the video if I had a question and then resume!

lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job

Disassembled dryer, removed tumbler, replaced drum support rollers

Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working

unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mounted new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).