All Installation Instructions for Kenmore Dryer 11088722892

Broken dryer door catch

Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.

Parts Used:

Door Catch Kit

Kenneth from UPPR MARLBORO, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Door would not stay closed - so dryer kept shutting off

Followed Youtube video - quick & easy

Parts Used:

Door Catch Kit

Barbara from NORTH EASTON, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Dryer drum wasn't turning

Found the belt was broken and the pulley wheel had melted, replaced the belt and the pulley, could not have been simpler. Watched the video on how to repair and in less than 15 mins was fixed. Saved a lot of money by doing it myself.

Parts Used:

Dryer Idler Pulley Assembly

Carrie from PLAINFIELD, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench (Adjustable)

1 person found this instruction helpful.

Was this instruction helpful to you?

latch was broke

just followed the video directions, worked perfectly thanks

Parts Used:

Door Catch Kit

Rick from SAN DIEGO, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

dryer would not run because catch did not hold tight enough to press door switch.

removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!

Parts Used:

Door Catch Kit

j from TAZEWELL, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Dryer would not start. After first replacing a spare Dryer Thermal Fuse I had it tripped again due to overheating. I then ordered a replacement Dryer Thermal Fuse as well as a cycling thermostat after determining the thermostat was no longer regulating the dryer's temperature.

Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.

Parts Used:

Cycling Thermostat - Limit 135/155

Mark from BLOOMFIELD, CT
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

dryer wouldn't stop when opening door

removed two screws in dryer vent released the catches on the top removed the two screws holding the switch releases the wire holder unplugged the wire and reversed the same putting back a peace of cake and part select very fast shipment

Parts Used:

Dryer Door Switch Assembly

Edward from FRENCHBURG, KY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Dryer door wouldn't catch and stay shut

I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair

Parts Used:

Door Catch Kit

Melody from TEXARKANA, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Kept running with door open.

Replaced switch very easy to do.

Parts Used:

Dryer Door Switch Assembly

Mark from NORTH READING, MA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

broken door catch

Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.

Parts Used:

Door Catch Kit

Frank from ENDICOTT, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Door catch was cracked

Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.

Parts Used:

Door Catch Kit

Tammy from glenford, OH
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Dryer wouldn’t stop spinning/2weeks later didn’t turn on at all

Lift up top portion of dryer inside the front wall is the electrical part which attaches to the door switch

Parts Used:

Dryer Door Switch Assembly

Theresa from STOCKTON, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

broken door catch

I followed your short video and found it very easy to do

Parts Used:

Door Catch Kit

Susan from HUDSON, MA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Dryer door would not stay closed

After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.

Parts Used:

Door Catch Kit