11086572501 Kenmore Dryer - Instructions

I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

Followed instructions for standard blower wheel replacement and repair kit installation, which were straight forward. The only real issue I ran into was removing the blower wheel, The instructions say to turn it clockwise and remove it, however this wheel had been on there for a long time and it also has a taper shoulder so it was not coming off without a fight which is why the dremel tool is listed. I had to cut the old bower wheel out in pieces so I could remove the electric motor, which was easy. Once out and on the bench and only the metal hub left on the shaft a 7/16" wrench and large vise-grips got it to break loose. The good side of this is it allowed me to blow out any lint that had built up on the motor, like new again.

The repair went well, using the whirlpool repair manual and looking at the video from PartSelect. The machine was a bit different than the one in both the video and the manual but that did not cause any problems. The only tricky part was to reinstall the belt "blind" behind the motor, easy to pinch your fingers and also get scratched by the sheet metal edges. To make it easier for that part I supported the drum with the old belt and a bungee cord to the garage frame so I did not have to hold it up and work under it at the same time. When the drum and new belt were in place I just cut the old belt, it was going to the trash anyway.. I replaced the belt and the tension pulley, witch was not turning easy and worn by the belt. I also put some grease ( SUPER-LUBE, www.super-lube.com) on all pulleys. It took about 2 hours because I am 78 years old and have heart problems.

Disassembled dryer. That was the hard part. Figuring out how to get the top off the dryer so I could get the drum out took the most time. The end caps on the control panel had to be removed by forcing them outward to release the plastic catches. Then the bottom corner screws were removed to allow the panel to swing up out of the way. The top panel could now be removed. To gain access to the belt and tensioner the blower and ducting off the front of the motor had to be removed to remove the belt. Now the drum was able to be lifted out. The motor swap was a cinch with no wiring modifications required. Reassembly was the reverse, with the most difficult thing being tightening up the blower fan. This required putting a wrench on the belt end of motor shaft and holding it while reaching thru a narrow gap on top of the fan ducting.

I followed the video provided by ‘Partselect’; although it was not the exact model it was close enough to get the job done with high confidence.

Just follow the repair video, it was easy!

I checked continuity of all electrical points. I took the top off, then the back, and front of the dryer off so it was easy to inspect the whole dryer. I was also able to clean unwanted dust, and lent with a shop vacuum by doing this.
Keep track of different screws, and mark each screw location with a permanent magic marker. Taking pictures with camera phone is very helpful. Pay attention to electrical connections as well, some of those will need to be dismantled.
Try not to take apart anything more than needed. Watching some online video's can be very helpful as well.
If uncomfortable doing this, call a service repair technician.
I'm a farm boy, and repairs usually come easy to me, but not always.

Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.

Confirmed I had incoming 240V, checked continuity on element switch confirmed bad. Ordered replacement part. U have to remove drum to replace element

Followed online video very easy and dryer works like new one....

Remove screws, dryer sensor on screen. Put sensor back in place. Secure with screws. The way you take it off go in reverse.

Watched video & took my time. It went easy

I found a simple video on YouTube. I removed the front panel and door. I removed drum and belt drive. Heater element was then easily accessible. I removed all wires after taking pictures of wiring. Element was secured by one screw and one clip and was easily removed. Removed element from element cover. Checked thermostat and thermal overload. Put new element inside of element cover. Then replaced everything in reverse order. Removing lint from inside of dryer was probably the most difficult part of repair. Had to have assistance from my son to put drum belt back on but rest of replacement was simple.

Before anything unplug the dryer
1) Remove the back panel to include electric cable. 2) Remove the lower front panel. 3) Remove top panel. 4) Remove control panel 5) remove door assembly to include metal frame and front panel of the blower housing. (much easier than trying to do this separately. 6) Remove drum belt by pulling back on the idler pulley (spring). 7) Remove drum. 8) Remove idler pulley retaining ring and pulley. 9) remove old seal on blower housing. 10) I added high temp grease to the pulley shaft and installed new pulley. 11) Install new blower seal. 12) Install drum and new belt. 13) Re-install all the panels.