All Installation Instructions for Kenmore Dryer 11084831300

Belt was raffling and there was aloud knocking sound

Removed the screws replaced the belt and lubricated the wheels and that fixed my Knocking and it runs like when I first got it

Parts Used:

Multi Rib Belt

Genette from CLEVELAND, MS
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

No heat from dryer.

1.Removed lower dryer cover - two screws. 2.Tested heating element circuit including high temp cutoff, - Heating element circuit was "open" so I first tested the heating element - "open" so I removed one screw on the side and removed the element - element broken. 3.Ordered the part - good price and the deliver was great, three days. 4. Cleaned any lint up and Installed the new heating element and front panel 5. Heated right up - probably saved myself a good $100 for less than thirty minutes of work!!!!

Parts Used:

Dryer Heating Element

Nelson from RAVENSWOOD, WV
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Clothes were not drying on auto sensor.

Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.

Parts Used:

Moisture Sensor

Michael from Annapolis, MD
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Dryer would power up. but would not start when start button selected

I referred to the dryers tech sheet for troubleshooting. The start switch was found bad. However, all other connection looked good and control module board appeared ok until I removed it from the machine. Found bottom of board, directly under the motor relay, scorched and burnt. All other components checked out ok. A new $300.00 board would be needed to fix the problem. Not worth fixing a 10yr. old machine! New dryer on order. Sometimes you just can't make a silk purse out of a sows ear! I returned the start switch that took over 8 days receive it. Lesson learned; electronic control boards have two sides. Always visually inspect both sides. It will save you alot of wasted troubleshooting time.

Parts Used:

Dryer Door Switch w/Wire

Andrew from OAK HARBOR, WA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Dryer would not start.

I watched the video or I would have likley just called a repair man. It took longer to clean behind the dryer than to install the new thermal fuse. After taking the back off the dryer is was as simple as changing a fuse. Dryer works like new for about $20 bucks and we avoided the hasle of getting a repair man, especially since we live in the country. Thanks for having a web site that is so easy to use and full of good information.

Parts Used:

Dryer Thermal Fuse

MONA from SHAMROCK, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Dryer would shut off mid way through cycle and give an E1 error code

After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back together in reverse. I also took the time to clean any dust and lint out.

Parts Used:

Dryer Thermostat Internal bias

Dwayne from Bainbridge, PA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set

5 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Old. Original heat seal was deteriorated and peeling off. Streaks were getting on the clothes.

Removed the front panel, removed the tub and removed the old seal. Tub seal area was scraped, sanded and wiped with acetone to ensure a clean. Bonding surface. Applied adhesive with and acid brush to get a consistent adhesive layer without getting too much in any one place. Seal was a bit smaller than the tub circumference so it had to be stretch to fit. While the adhesive was curing , I took the time to clean the contact surfaces and vacuum the lint from inside the cabinet. Reinstalled the tub, drive belt and front panel.

Parts Used:

Dryer Drum Seal with Adhesive

Lawrence from ARITON, AL
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers, Socket set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Hard to reach the screws inside the dryer They were on the door side of the dryer and hard to reach, especially if you are a abig guy.

Removed the dryer door, unscrewed lint vent.

Parts Used:

Moisture Sensor

Lucy from CHADDS FORD, PA
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Making a racket.

Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.

Parts Used:

Dryer Drum Support Roller

Carl from MARION, KY
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

dryer making noise. order parts

YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!

Parts Used:

Dryer Drum Support Roller

Thomas from TULELAKE, CA
Difficulty Level:
Very Difficult
Total Repair Time:
30 - 60 mins

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

cold air vent in dryer was broken

remove 3 screws vent comes out put new part in works grate just like new a gain

Parts Used:

Outlet Screen Door Grille

Moisture Sensor

MIKE from WESTLAND, MI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Squealing when running

You tube and supplied video directions for the make and model. Follow step by step and the repair went easy. Worried when removing the dryer drum but it went smooth.

Parts Used:

Idler Pulley with Bracket

MICHAEL from Baden, PA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

My dryer would not heat. Drum was spinning fine and everything else was working just no heat.

I removed the base cover and cover over my lint blower. The thermal fuse is located on top of the blower housing. I removed the thermal fuse utilizing a small nutdriver and installed the new fuse.

Parts Used:

Dryer Thermal Fuse