All Installation Instructions for Kenmore Dryer 11084722400

drum support roller was squeaking VERY loud

lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job

Parts Used:

Rear Drum Support Roller Kit

joe from southgate, MI
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Worn bushing on bottom drum roller

unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mounted new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).

Parts Used:

Rear Drum Support Roller Kit

Dryer Drum Roller Shaft Left Side

Frank from Avon, CT
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Socket set

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Loud noise while in use

Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working

Parts Used:

Rear Drum Support Roller Kit

Josh from Madill, OK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

broken door catch

I followed your short video and found it very easy to do

Parts Used:

Door Catch Kit

Susan from HUDSON, MA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Dryer door wouldn't catch and stay shut

I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair

Parts Used:

Door Catch Kit

Melody from TEXARKANA, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Kept running with door open.

Replaced switch very easy to do.

Parts Used:

Dryer Door Switch Assembly

Mark from NORTH READING, MA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

broken door catch

Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.

Parts Used:

Door Catch Kit

Frank from ENDICOTT, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Door catch was cracked

Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.

Parts Used:

Door Catch Kit

Tammy from glenford, OH
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Dryer wouldn’t stop spinning/2weeks later didn’t turn on at all

Lift up top portion of dryer inside the front wall is the electrical part which attaches to the door switch

Parts Used:

Dryer Door Switch Assembly

Theresa from STOCKTON, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

dryer wouldn't stop when opening door

removed two screws in dryer vent released the catches on the top removed the two screws holding the switch releases the wire holder unplugged the wire and reversed the same putting back a peace of cake and part select very fast shipment

Parts Used:

Dryer Door Switch Assembly

Edward from FRENCHBURG, KY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

The door whould not close enough for the dryer to work.

Got my parts very quickly.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.

Parts Used:

Door Catch Kit

Frank from Union Beach, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Broken dryer door catch

Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.

Parts Used:

Door Catch Kit

Kenneth from UPPR MARLBORO, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Door would not stay closed - so dryer kept shutting off

Followed Youtube video - quick & easy

Parts Used:

Door Catch Kit

Barbara from NORTH EASTON, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Dryer drum wasn't turning

Found the belt was broken and the pulley wheel had melted, replaced the belt and the pulley, could not have been simpler. Watched the video on how to repair and in less than 15 mins was fixed. Saved a lot of money by doing it myself.

Parts Used: