11082824100 Kenmore Dryer - Instructions

I removed all of the screws on the inside of the door. Unfortunately, I found out that I only needed to remove four of the screws after the glass fell out of the door. After re-installing the glass and removing the correct four screrws, I figured out that I had to pry off the plastic face plate to get to the two screws that held on the handle. After removing these screws, I was able to get the broken handle out and the new handle in. I then reinstalled the plastic face plate and replaced the four screws that held it in place.

Checked this site for most likely needed parts and ordered. Located full repair manual inside unit after removing lid. Followed instructions in manual to take apart and remove the drum; took pictures at each removal step and used pill organizer to keep screws in correct order and quantity. The metal cylinder in the center of the idler pulley had ground away so the idler pulley with bracket was replaced. (There was a lot of metal dust that had to be cleaned.) One of the rollers did not turn smoothly so that was also replaced. After putting drum back in, reversed the steps to reassemble and referred to photos to make sure did in correct order and did not forget anything.

The repair was done by following the instructions on this website. I'm a 68 yr old female who has surprised myself by finding the part I needed, ordering it and did the repair all by myself. My son was at the house and said he would do it for me and I told him I wanted to try myself first and if I needed assistance I would let him know. He showed me where the Phillips screw drivers were and chose the correct size and then proceeded to take off the 4 small Phillips screws on the door and the 2 at the bottom of the door under the window area. Then I removed the panel and the broken handle and replaced with the new one. Then put the panel back on the door, screwed the 6 screws back where they belonged and the job was completed. I was so excited that I actually did the repair but best of all my son was proud of me for even attempting the project.

Just like the video, just followed the video
Thanks,

Just replaced part

Disconnected Power cord, removed vent pipe, removed back panel, had to slide top cover off to remove additional screw holding back on. Went down to where the Idler Pulley was, removed old piece by depressing on the spring loaded actuator and slid it off the belt and all. Replaced same as removal.

Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.

The pulley is accessible from the back of the dryer. Disconnect the gas line. Remove all the screws. Also remove the small plate that secures the line cord. Lift the back up and out. I was able to avoid disconnecting the water line. Take a picture of the pulley so that you will have a record of the belt routing. Release the spring and remove and replace the pulley and bracket. Vacuum out the lint. Plug in the dryer to make sure that it works properly before reassembly.

Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair

take off front bottom panel. use ohm tester on the heater coil element, (It had broken in back) remove screw holding it in place and the two red wires leading to the element. Pull out and replace. reinstall in reverse. Done

Note that the problem was with the pedestal, not the washing machine. In the process of attaching the two units together, the drawer in the pedestal is removed. When I tipped the assembly up, the slide slid out and locked horns with an object, bending the slide. The slide is an easy replacement. Just one screw holds it in place. A slot in the slide mates with a tab to hold the back side of the slide in place.

I Googled a description of the repair, found a forum entry from another 'do-it-yourselfer'. They had posted instructions on which 8 screws needed to be removed. I followed the instructions and within 15 minutes, I was done.

I removed the bottom access panel, with 2 hands i reached in behind the blower, i released the belt, i used a screwdriver to pop the retainer from the pully spindle, i removed and replaced the pully, i snapped the retainer back on and replaced the belt. I made sure the belt was on track and all was good. I put the bottom panel back on, it took all of 5 minutes. The hardest part was the retainer clip faces the rear of the dryer so you have to feel it. Also , the space is tight, use a smaller flathead screwdriver to get behind the clip, it will pop right off.

Remove old filter
Vacuum out
Install new filter

Not a handyman but this was an easy and cheap fix. Now the automatic settings are working and drying much faster. Unplug machine, front panel has 2 spring clips toward the edges that you stick a flat tool into and pull on the panel to open. Pull off the electrical connections from the old sensors by the right side of the lint screen. Needlenose pliers help with the one farther up there. Then just pull the old ones sensors out, stick the new ones in, reconnect the electrical and get ready to live the good life with dry clothes that don't smell musty.