11082722200 Kenmore Dryer - Instructions

just like the guy in the video. It was easy to folow his instructions, and the best thing of all i could stop the video if I had a question and then resume!

lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job

Disassembled dryer, removed tumbler, replaced drum support rollers

Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working

unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mounted new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

1. Popped off hinged dryer lid at front and supported to allow access to lint chute
2. Removed back sheet metal panel
3. Removed dryer chute to expose sensor; removed same-deformed terminal on top needs to be straightened with pliers to remove through slot.
4. Installed new sensor; terminal needs to be twisted to ensure solid installation and good ground. Bottom pops in but took a bit of finagling.

Accessing and replacing the sensor was straightforward enough; bulk of the job was cleaning off old gasket material (severely degraded) in two locations. Used plastic scraper and razor blade scraper, then cleaned sticky with goo gone. Installed new gasket strip from Home Depot; available in rolls. I used 1/4" x 3/8". Surprising how much lint/hair/debris was in bottom of lint chute. Glad to get it all clean.

I would not ever consider this a repair. The dryer filter cracked because of my wife put it in loosely. The new one just fit right in.
What was so good about the entire process was how quickly I recieved the part. A matter of two days.

Excellent and super easy. Owned the box and snapped the new one in. Ready for laundry again in a matter of minutes.

Well turned off power by unplugging it. Took a Phillips screwdriver and took the 2 screws out from vent and then took a flat head and left up each side to access the inside of dryer. Then used screwdriver to take out screws to switch and then disconnect the power cord to that. Reverse the procedure and it was so simple. Ty. Awesome company.

Watched a you tube video that told me exactly how to do it. Saved us from going out and buying a new one. My husband and I were very proud of ourselves because just to get someone to look at it would have cost us $85. The part was only around $25.

Unplug electrical
remove 2 screws from lent screen handle
remove lent screen
using putty knife, insert about 2" from each side at the front of the dryer just below the top cover to release 2 keepers.
pull up on cabinet top and lean top backwards out of the way.
remove 2 screws holding the switch located at the top right inside of the dryer door.
pinch the plastic keeper while pushing down to release wiring assembly from dryer cabinet
using a small blade screwdriver, disconnect wiring connection
discard old assembly
reverse all steps to replace with new door switch

Didn't need a repairman for this project! Ordered the part (seems like on Sunday) and got it really quick (the next Wednesday). Opened the package, placed the part where it was supposed to go and shazam!!!! Fixed it was quick and easy!

removed two screws from filter acess and raised top of dryer to acess switch, easy remove and replace, thanks.

The video shows you all you need to know