Models > 11078415810 > Instructions

11078415810 Kenmore Dryer - Instructions

All Instructions for the 11078415810
121 - 135 of 341
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
broken door catch
I followed your short video and found it very easy to do
Parts Used:
Door Catch Kit
  • Susan from HUDSON, MA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door latch broke
Pop out the old latch and replaced with a new one
Parts Used:
Door Catch Kit
  • Debra from Oakland, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
catch was missing to close dryer door
The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)
Parts Used:
Door Catch Kit
  • DONNA from SAN LORENZO, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door catch broke therefore dryer door would not close
just put the new part in the door---sooo easy! THANK YOU!
Parts Used:
Door Catch Kit
  • vernette from sprague, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Won't pump out the water
Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.
Parts Used:
Lid Switch
  • Victor from NORFOLK, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
latch was broke
just followed the video directions, worked perfectly thanks
Parts Used:
Door Catch Kit
  • Rick from SAN DIEGO, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer would not run because catch did not hold tight enough to press door switch.
removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!
Parts Used:
Door Catch Kit
  • j from TAZEWELL, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken dryer door catch
Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.
Parts Used:
Door Catch Kit
  • Kenneth from UPPR MARLBORO, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door would not stay closed - so dryer kept shutting off
Followed Youtube video - quick & easy
Parts Used:
Door Catch Kit
  • Barbara from NORTH EASTON, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer drum wasn't turning
Found the belt was broken and the pulley wheel had melted, replaced the belt and the pulley, could not have been simpler. Watched the video on how to repair and in less than 15 mins was fixed. Saved a lot of money by doing it myself.
Parts Used:
Dryer Idler Pulley Assembly
  • Carrie from PLAINFIELD, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken door switch
I took out the 2 screws that are located on the top of dryer under the lint filter door. Popped up the whole top of dryer. Opened the dryer door to unscrew the 2 door switch screws. Took off the old broken door switch through the open dryer top and before replacing the new door switch completely I tested it by turning the dryer on and pressing the new switch against the button activator 2 find out if it works. When it did, I carefully put the door switch back so the dryer door can activate it properly and screwed in the 2 screws. Finally, I put the dryer top back down & fastened the last 2 screws under the lint filter door.
Parts Used:
Dryer Door Switch Actuator
  • john from el paso, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Was too old
I just changed for the new one! 2 seconds.
Parts Used:
Dryer Lint Filter and Cover
  • HELOISA from BOCA RATON, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door whould not close enough for the dryer to work.
Got my parts very quickly.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.
Parts Used:
Door Catch Kit
  • Frank from Union Beach, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer wouldn't turn on
I removed the two screws on the top by the lint catcher. Then, per information from this website, I pried up the top. I reached down into the dryer and removed the two screws on the broken door switch and replaced it with the new part. I am a recently widowed, 55 year old and was thrilled to find good advice, information and instructions on your website!! Simple as could be!
Parts Used:
Dryer Door Switch Actuator
  • Kim from Northridge, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer door wouldn't catch, catch was broken
took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......
Parts Used:
Door Catch Kit
  • Theodore from Tyler, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 11078415810
121 - 135 of 341