11078410410 Kenmore Dryer - Instructions

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

I diagnosed the problem, as a broken arm on the actuator for the door shut switch. I jumped the switch, and dryer worked. I went to this site, found the part I needed, ordered it/received it quickly, and proceeded to do the repair. The video that THIS particular part goes for, isn't' like MY dryer. My dryer hinges in the rear. You just remove the 2 screws on either side of the control panel, (right and left), pull forward on the panel, to ease its attachment, let it lie. Then with a small plastic pry tool, pop the 2 attaching points in the front of the dryer. Front end lifts up, like a hood on a car. My roommate held hood up, while I R&R'd the switch actuator. Went back together, in reverse of my taking apart. Worked great. Thanks a bunch.

Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,

Your great service is very hard to find.

Removed 2 screws holding the lint trap on top, popped up the top and lifted back, removed 2 screws on the inside top of front panel, lifted front off and set aside then reached under the drum and pulled tension pully to loosen the belt, and removed the drum. popped the motor clams off and then used 2 adjustable wrenches to grasp the nuts at the front and back to remove blower fan. When you look for the area in back to loosen the blower fan you may notice the nut that you are looking for is actually part of the fan and is plastic looking rather than metal. I did have to take off the back cover to the blower fan to tighten it back up.I had seen instructions that the blower fan would have a 3/8 hole in the back of it to loosen it,but mine did not. I assembled it and it works great with my new motor and rollers. I received my part in 2 days, very happy

Took of the btm pan and the top to be able to remove the front. Raised the drum enough to replace the right hand wheel. ( the old ones had already been removed) Replace the left hand wheel and bracket. Re assemble the machine. Worst part was trying to do all this with the can of beer in one hand!!

I replaced a bad thermostat

I watched the part select you tube video that links specific loud dryer noises to specific broken or loose parts. It allowed me to identify the part I needed, which I ordered through their website. Two days later, I had the part and installed it, with help from another online video that showed me how to take the dryer apart to install the drum support roller. Thank you, the information provided made the repair quite easy. It works perfectly now!

After identfying that the problem was due to a damaged drum support roller, I decided to replace the bad roller instead of replacing the dyer itself.

The first thing was to remove the front cover
and the front panels to expose the drum. (Only a few screws hold them in place.) Next, the drum was removed by first releasing the belt from the motor pulley and tensioner, and then pulling the drum straight out.

At this point the two rollers would be exposed. The triangular plastic retaining locks were removed by slightly prying them off. The old rollers were then removed and replaced.

Before putting everything back, this was a good time to vacuum all the accumulated lint inside, especially the lint that had accumulated around the motor assembly and the fire box.

(A pleasant surprise: I found a lot of coins inside the unit, enough to recoup half of what I spent for the new rollers.)

Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.

Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.

Found the belt was broken and the pulley wheel had melted, replaced the belt and the pulley, could not have been simpler. Watched the video on how to repair and in less than 15 mins was fixed. Saved a lot of money by doing it myself.

Followed Youtube video - quick & easy

just followed the video directions, worked perfectly thanks

removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!

Replaced lid switch, but problem still continued.