11074670120 Kenmore Washer - Instructions

Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?

Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.

Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said. I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.

took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at

>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!

1) Using a Phillips head screwdriver, the two screws retaining the hinge pin to the lid were removed. 2) Remove hinge pin and tilt lid slightly to gain access to bushing hole. 3)Install new bushing in hole. 4)Reposition lid. Insert hinge pin through lid and into bushing. 5)Reinstall hinge pin retaining screws and tighten.

replaced the faucet adapter I did not save when I change out the kitchen sink faucet set

My wife did the repair. Went on your website and watch the video on how to replace the switch and she was able to do it herself. I didn't mind at all. Saved $75.00 service charge.

1)Shut off power supply to dryer. 2)Removed lint filter. 3)Removed two screws that secure filter duct to dryer top. 4)Lifted front of top to gain access to door switch. 5)Removed two switch mounting screws. 6)Removed the two power leads. 7)Reconnected power leads to new switch using "Normally Closed" terminal on switch. 8)Reversed the previous procedures to complete repair.

I bought the portable dishwasher on Craigslist, and it didn't have the connector that goes on the kitchen faucet. Ordered it here, got it in a few days, and didn't need any tools - just had to screw it on. Good as gold!

I knew I needed a faucet adapter, but thought I could just go to my local home depot and get the part...not so much. After 3 trips and not getting the part I truly needed I ordered the part from partselect. I received it literally the day after I ordered it, screwed in place with no tools, attached the coupler/hoses to the faucet and washed dishes. I wish I would have ordered the part from partselect before even bother with home depot. I would have saved myself a lot of trouble! Extremely happy! Thank you!

replace the water valve

Removed the old one installed the new one

Ordered a new Faucet Adapter! Simple

Found the adapter on Parts select through a google search. Unscrewed the existing faucet aerator and srewed in the adapter. The plastic shrink wrap holds the washer and screen in place, so don't open it until you're ready to install. Finger snug does it, only use the pliers to remover the old aerator from the faucet. Normally, I don't use pliers, but both of these parts were round and had vertical serrations to engare the plier teeth.