All Installation Instructions for Kenmore Dryer 11068082701

Squealing pulley

Removed rear cover. Released tension on spring to pulley to remove belt from pulley. Used a socket to remove idler. Did the reverse to install.

Parts Used:

Idler Pulley Wheel and Arm

Randall from MILLSAP, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Socket set

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Door would not close after I slammed it.

Simple with the Instructions in the video.

Parts Used:

Dryer Drum Support Roller

Dryer Door Catch

Jeffrey from FRANKLIN, MA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Drum support roller making very loud noise

had to take front off of Dryer then was able to replace drum roller

Parts Used:

Roller Support Tri-Ring

Drum Support Shaft - Rear Shaft with Left Hand Threads WPW10359272

Dryer Drum Support Roller

William from TROY, AL
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Dryer wasn't heating.

Replaced high limit thermostat and thermal cutoff. Dryer works like a champ. Reviewed couple of YouTube videos that showed clearly how to
get to the effected parts, test them and replace them. I had an old front loading dryer once before that I repaired a couple of times but these parts were accessible by removing a panel on the rear of the unit. The procedure was more involved with this unit. After studying the videos and getting a feel for what was involved, the process, while involved, was fairly simple and putting the unit back together was also fairly easy. Replacement parts did the trick. Very happy.

Parts Used:

High Limit Thermostat

Thermal Cut-Off with High Limit Thermostat

Bob from OMAHA, NE
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Old lint filter was broken

Just replaced the old lint filter.

Parts Used:

Lint Filter

Earl from Santa Ana, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

8 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Lint filter seal worn out

The part wasn’t for my machine. Unfortunaly I was not able to repair it. I was sent stripe of foam with an adhesive strip on the back. I needed a felt strip.

Parts Used:

Dryer Seal Outlet Housing

Dennis from PALM BCH GDNS, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Very noisy from support wheels

Changed all 4 drum support wheels and belt tension arm

Parts Used:

Idler Pulley Wheel and Arm

Dryer Drum Support Roller

Steven from WICHITA, KS
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Socket set

7 of 12 people found this instruction helpful.

Was this instruction helpful to you?

door would not latch

removed old latch with pliers - inserted new latch

Parts Used:

Dryer Door Catch

Paul from BENTONVILLE, AR
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Dryer drum turned hard because rollers were worn

Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.

Parts Used:

Dryer Drum Support Roller

Paul from STONE CREEK, OH
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Roller Berings were worn out - replaced both

Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair

Parts Used:

Dryer Drum Support Roller

Gregory from COCOA, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

dryer making noise. order parts

YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!

Parts Used:

Dryer Drum Support Roller

Thomas from TULELAKE, CA
Difficulty Level:
Very Difficult
Total Repair Time:
30 - 60 mins

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Clothes were not drying on auto sensor.

Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.

Parts Used:

Moisture Sensor

Michael from Annapolis, MD
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Dryer would not start, showed F40 code

Very easy do it yourself repair, and saved at least $300.00. I watched a video and it took me less than 20 minutes to complete repair. Part fit perfect and I have already ordered another to keep as a spare.

Parts Used:

Dryer Disposable Thermal Fuse

Glenn from KINGSPORT, TN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

a portion of the felt seal was torn loose on the inside of the dryer and needed replacement

I spent the most time researching and confirming exactly what part I needed before ordering the shipment. The illustrations and videos available on how to replace the part(s) were VERY helpful and much appreciated.

I followed the instructions seen on video and removed the top and front of dryer. Then pre-fit the new seal - and stretched it out some while dry to make sure it fit the drum. Once fitted, then I glued 1/2 of it and let it stand for at least 30 minutes and then did the 2nd 1/2 after that. I sure needed clips to hold it in place before moving on to complete both halves. Then I tested it and it tested ok.

I have only noticed 1 spot where some adhesive ran out that shows but it was minor. Had to figure out how the main drive belt work with the pressure pully because it had come loose from the drum. Once past that - it just needed reassembly.

Parts Used: