Models > 11068072801 > Instructions

11068072801 Kenmore Dryer - Instructions

All Instructions for the 11068072801
91 - 105 of 218
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Rollers making a noise.
Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.
Parts Used:
Drum Support Shaft - Rear Shaft with Left Hand Threads WPW10359272
  • Carl from MARION, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Socket set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer not heating
Confirmed I had incoming 240V, checked continuity on element switch confirmed bad. Ordered replacement part. U have to remove drum to replace element
Parts Used:
Dryer Heater Element
  • James from GREENVILLE, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer electrically dead
Unplugged power cord. Removed rear panel screws and panel . Removed the two wires connected to part. Removed two screws holding part and replaced all components in reverse order.
Parts Used:
Dryer Disposable Thermal Fuse
  • Dale from Anderson, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The fan wheel had a blade break off, my bad.
I went on the site and found the part I needed and then watched the video explaining how to dismantle, replace the part, and put the dryer back together. It was easy, especially with the video instructions.
Parts Used:
Dryer Blower Wheel
  • Terry from ETTERS, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The lint filter needed replacement due to what is probably normal wear and tear.
I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.
Parts Used:
Lint Filter
  • Donna from CARY, NC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Screen ripped
Dropped new filter in.
Parts Used:
Lint Filter
  • Cindy from BENZONIA, MI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer kept throwing the E1 error indicating the thermistor needed replacement
Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back in, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.
Parts Used:
Dryer Thermostat Internal bias
  • Rory from LEESBURG, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door seal came off
Did not take the door off..applied adhesive and seal fit perfectly..used packaging wide tape to secure for a bit while adhesive dried..waited 24 hrs..holding well..dryer is back to working order..thank you..I received the seal in 2 days after ordering!!
Parts Used:
Door Seal with Adhesive
  • Mary from MEQUON, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door wouldn't shut
Looked up on the internet, saw a video, ordered the part using model of dryer, got the part in 7 days, took out old part and snapped in the new door latch. Now it works good as new
Parts Used:
Dryer Door Catch
  • Jean from CARROLLTON, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door catch was broken
Took a screwdriver and bent wings out a little and then was able to get hold of it with a pair of pliers. Then just put the new unit in the opening and tapped it in. If I had a good pair of needle pliers, it would not have been necessary for the screwdriver.
Parts Used:
Dryer Door Catch
  • Earl from FRISCO, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door catch broken
Didn't have a putty knife, so used a flathead screwdriver to carefully pop out the top, then bottom of the catch. New one easily popped in. Took less than one minute!
Parts Used:
Dryer Door Catch
  • Polly from POTTSVILLE, AR
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door catch broken
Push in new catch...close door.
Parts Used:
Dryer Door Catch
  • ROBERT from GAINESVILLE, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Catch broken
Took Putty Trowel and pried out top and bottom then pulled out with needle nose pliers, new part just pops back in (be sure flanges are on top and bottom not sides).
Parts Used:
Dryer Door Catch
  • Forrest from PARIS, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door catch broken and fell into door
snapped new catch into door
Parts Used:
Dryer Door Catch
  • Phillip from FORSYTH, MO
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door catch on our Whirlpool Dryer had given out.
The repair cost us less than $9.00 and about 1 minute to repair. You can only imagine how much a tech would have charged us!! We are so very happy that we discovered this site . The instruction video they offered, the customer service via their website AND quick delivery of the part, has insured them that we will be repeat customers. Thanks so much !!!!! Bravo! Annie & Peter in , Nevada
Parts Used:
Dryer Door Catch
  • Annie from HENDERSON, NV
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 11068072801
91 - 105 of 218