11066112500 Kenmore Dryer - Instructions

Used the YouTube video sent by this site

I opened up the dryer as per the instructions I had received from PartSelect tech support. It was very easy to do. The only unexpected thing was that the original belt had snapped and in doing so the idler pulley was actually laying on the floor of the dryer's bottom. I had to figure out how it went, but that only took a minute and I popped it back into place. I held the drum by hand while pulling the dryer face away so it wouldn't fall and then I slipped the belt over the drum and quickly closed the front up again. I aligned the belt on the spot where the old one had been, pulled it through the idler pulley and over the motor and voila. Done. I closed up the dryer and was on to another "Honey Do" project within 20 minutes.

my dryer door didn't latch for over a year. We were accustom to proping large objects against it. a friend told me to look on line. The close up pictures and parts diagrams were awesome. It was here in 4 days . Now my family thinks I am a hero. The end

Removed the two screws under the lint trap
Opened the top (had to use flathead screwdriver to release latches)
Disconnected door switch harness from front panel
Removed 2 screws holding front panel on dryer
Lifted out dryer drum (previous belt had broken)
Vacuumed inside of dryer (found $3 in quarters!)
Put new belt around drum
Put drum back in dryer, using empty laundry soap bottle to support its weight
Looped belt around pulley and motor; secured pulley to dryer bottom
Made sure rear gasket thingy was aligned properly and drum turned freely
Put front panel back on
Re-attached door switch
Closed top and put screws back in under lint trap
Fired it up - WOOHOO!

I lifted the top of the dryer cabinet, like the hood of a car using a screwdriver to pry it open. I removed the two screws in the upper right corner of the cabinet front. I disconnected the safty switch on the front door. The front of the cabinet can then be removed by lifting up the front off the pins in the base. With the drum exposed you can place the belt on and thread it through the two pulleys on the motor. Consult the diagrams provided on the PartsSelect website for the proper positioning of the belt on the pulleys. After the belt is installed spin the drum by hand one turn to make sure that it is seated properly on the drum and pulleys. Reassemble the dryer in the reverve order.

Used this resource and others' advice -thank you . Make sure to disconnect power first. I had replaced the rollers and tensioner a week earlier due to squeaking, but mine was the rare one where squeaking meant motor failure, so I had to place another parts order. The dryer was 19 years old, and my blower wheel did not simply 'unscrew with reverse threads'. During removal the blower wheel's plastic deformed, so had to do like someone else did and cut the rear shaft with a reciprocating saw. Just be careful not to damage the bulkhead's built-in bracket that anchors the rear of the motor. I think it was a 13/16" wrench that fit the blower wheel and I forget the size for the pulley nut on the front of the motor, but I suggest a deep socket since it held well. My best advice when dealing with a motor replacement is to ensure the blower wheel wheel will separate successfully from the motor before placing your parts order should it be a stubborn removal. Good luck.

I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

I took the dryer apart ( using a repair book ) It was Super Simple to do I only needed a extra set of hand's to hold the drum in place while reassembling it. removed the hold down snap on collar's on the Motor ( after removing the Blower from the back of the dryer ( super simple. Extra set of hand's needed ) Reassembled in the same order. And now The Dryer work's like NEW..Shure Beat Buying a new Dryer..

When the problem first came up, I took the dryer apart without first looking up any instructions. This wasn't difficult, but didn't realize when removing the fan from the motor, there is a square lug as part of the fan hidden by the rear clamp securing the motor. I was able to remove the fan by holding the motor shaft with a crescent wrench and removing the fan by hand, but was difficult and gloves were necessary in case the fan loosened quickly and my hand came in contact with the sheet metal (very sharp).

I took the motor out and attempted to clean it as it was loaded with dust as was the dryer internals. I tried to lube the motor bearings and appeared to free up, but the sight of metal shavings on the rear bearing seal had me concerned. This ultimely did not work and was trying to buy some time until the new motor arrived.

This is when I looked up the motor part number and found that Parts Select had the part number in stock. I ordered the motor on a Saturday afternoon and got a quick response acknowledging my order. The motor shipped that following Monday from Fresno and arrived on my Southern California doorstep Tuesday. These guys have their act together and are helpful in making the repairs. In my case I did not have to make any adjustments to the wiring or the pulley for my model and replaced the motor the following weekend in about 45 minutes. Since I had the unit apart several times before replacing the motor, the installation went quickly.

The dryer is again working fine for a unit 12 years old and my wife is once again happy that we didn't have to purchase a new dryer.

I raised the top of the dryer, removed the front, the belt and the drum. Slipped off old rollers, installed new ones and new tensioner. Reinstalled drum and belt, bolted front back on and closed the top.

I watched the video on how to diagnose problem and then how to repair . Videos were very helpful. Also the parts were ordered on line and arrived in 2 days. Parts at a local appliance parts store were twice the cost of what I paid for the parts from PartSelect.

pressed clip into hole on top of front panel. first remove two philip screws that hold filter so you can lift top up.

Watch the utube video a few times. Followed instructions. Marked all screws. Cleaned the inside of dryer where motor is. Replaced drum seal and then belt. I replaced front of dryer screwed everything in place and I did it. Holding drum in place while installing front of dryer was hard as it was heavy but I did it m. My friends and husband couldn’t believe it. Utube is great!

Half of my pulley was broken off so there were no wrench flats to take it off. I was able to remove it using Channel Locks and the 7/16 wrench shown in the video.

Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.