11065212610 Kenmore Dryer - Instructions

Followed the video and stopped at each part not one issue very easy repair most difficult was separating the electric from from panel a little tricky to get apart.

This model you cannot lift the top lid without breaking it. Removed the exhaust hose and back of dryer. vacuum out the dryer and hose to remove the excess lint. Remove screws from the lint guard mounting. Loosen and remove 4 screws that hold the lint guard in place. The seal at the base of this assembly was missing the seal around the discharges fan. Remove seal with putty knife. Use a small brass wire brush to remove as much as you can. Vacuum area. Reinstall the lint guard assembly, start at the top, gently life and push assembly up and in. You should be able to determine how far. Start the bottom 4 screws, tight them. Check fit. Then put the screw back in on the lint guard on the top of dryer. Once you have completed this connect exhaust hose. Start dryer, check the dryer exhaust vent that is outside. If the flow is good, WELL DONE!

Recommendation: Check this assembly by removing the back of the dryer approximately every 6 mos. for lint build up. Not doing this may increase the risk of fire.

Removed the back panel of the dryer. Thermostat is located in the out going air flow near the exhaust. Removed one screw that held thermostat. Exchanged wires and put everything back together

just remove 4 screws removed the drum and put the affected part and that's it

Replaced thermostat on back of dryer, very easy to do, took about 15 minutes after watching video . doe's not require rocket scientist to do.

Took back cover off, unhooked wires,removed screws,removed heating element,put new element on and reinstalled everything else..Now it has great heat!

Pulled Dryer away from wall and unplug. Removed back cover. Used my ohm-meter to check fuse ok. Then checked heater element no continuity. Removed two screws and three wires holding unit in place. Visibly checked coils and found break so I knew that was the problem. Ordered heating element and replaced in reverse order. Solved the problem now have dryer that works again.

Checked components that could be the problem as shown in the trouble shooting video, such as the fuse or thermal overloads. All of these checks are done with the multi-meter in the resistance (ohm) mode. All checks were good until the heating element check showed no continuity. Removed the heating element and could visibly see the break in the coil. Ordered the heating element. Installed it. The dryer works fine now producing heat as it should. THESE CHECKS ARE DONE WITH ELECTRICAL POWER TURNED OFF, UNPLUGGED, DISCONNECTED. FOLLOW INSTRUCTION VIDEO. Thankyou

removed door and front panel this exposed all the control devices I changed out the thermostat ndn repaired the dryer

Thank goodness the part was still available for a 25 year old dryer. Website was great to help solve the problem and the video was wonderful to show me how to identify the part and how to get to it. You take off the back of the dryer and then unscrew the thermostat from it's mooring. Undo the 4 wire connections. Stick in the new thermostat and re-install. Thank you!

The toughest part of the job was due to the fact that I was working in a small 1st floor laundry room. I had to pull the dryer out from the wall in order to get to the rear and squeeze between it and the washer to get behind it. I could not pull it out all the way because the 220 cord is only so long and the vent comes out also. After that, I unplugged the power cable, removed the vent, removed the back with my nut driver, disconnected a couple connectors, removed the existing heat element with my nut driver. Then I installed the new heating element and continued with doing all of the above in reverse. My wife is happy! Best of luck to all....Jerry

Took off back of dryer, removed screws from
heater unit, replaced wire for wire on to new unit,
I could not replace all screws, no hole in new unit.
all work great.

Removed the back cover off the dryer removing 9 screws. Heating element was in lower right corner as described on your site. We removed the screws holding it on and using pliers disconnected the two wires. We had to use one piece from the old element so keep it until all the repairs are complete. We reconnected the two wires and replaced the cover. We were ready to go then. We are not good at applaince repairs but with the directions given at your site this was so easy. Thanks!! I am sure this saved us so much by doing it ourselves.

Thank goodness for the video!!! Really helped. Removed screws from back, loosened wires and screws on old element. Toughest part was getting thermostat off of old element. Video mentioned screws, my unit was attached via a metal tab. Took some figuring to get it apart and not damage thermostat. Getting new unit into venting was tight fit - had to fit juuuuuusst right. Re-attach screws, plug it in to test - hot air. Reassembly no problem. I am not a real handy guy so for me to say this was easy means it was really easy.

I unplugged the machine and removed the back panel with a 1/4" socket. I unplugged each thermostat in turn and pulled them out. The internal bias was a bit tricky to remove without breaking the tabs or wires. I then placed each thermostat back in and replaced all the wires. Not bad at all. Weird thing is the dryer heats just fine now, until I put the back panel on; once I replace the back panel, it will not heat.