11062054100 Kenmore Dryer - Instructions

Disconnected Power cord, removed vent pipe, removed back panel, had to slide top cover off to remove additional screw holding back on. Went down to where the Idler Pulley was, removed old piece by depressing on the spring loaded actuator and slid it off the belt and all. Replaced same as removal.

Just replaced part

Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.

Turned off my circuit breaker first. Removed back panel with a 1/4 nut driver. Replaced the dryer fuse first. Very easy but did not fix the problem. Watched how to videos to narrow down the parts I might need. Purchased the thermal cut off kit. Installed the High limit thermostat first. Tested the dryer, no dice. Finally installed the Thermal cutoff. BAM!! I have heat. Since this is an older dryer I did need to use some WD40 to loosen some of the connections. Total cost of parts including tax and quick delivery was $48.30. Fantastic. My old man told me it was unfixable. He was wrong. I WIN. This site is a great teaching site. Thank you!

i took off the back of the drier and with a screw driver removed the 2 screws and put the new part on

Removed the back of the dryer about 8 screws. Removed the Thermostat 250 F and replaced with new. Dries a load of clothes in one cycle on medium. Not bad for a 16 dollar part. I am a computer tech and I am used to taking computers a part but I think most people that are in anyway mechanically inclined and can look at a diagram could do this and save yourself a lot of money.

Opened access door, noticed main power wire to heating element was partially melted. This was caused by a bad connection to the drying element, loose. Removed heating element assembly. Cut bad section of wire and added new connection. While doing this the thermostats plastic casing cap came off ! Probably due to exessive heat / resistance from the bad connection. This confirmed why there was no heat. Intalled new thermostat and and am now good to go !

I removed the back panel and tested the Thermal Fuse, the Thermostat and the Heating Element with a meter. The Thermal Fuse gave a bad reading. I proceeded to clean the dryer and lint pipe of all lent. I installed the new Thermal Fuse and put the back panel back on the dryer. The dryer worked for two loads of clothes and the Thermal Fuse blow again. I'm now at the end of my rope. I don't know what else to check and I can't continue to buy parts for only two loads. I guess I will have to invest in a new dryer.

Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair

unplug the dryer used nut drive to take the back off unhook the hose from dryer . disconnect the wires. remove the 2 screws from thermal cut -off . install the new parts

Very easy do it yourself repair, and saved at least $300.00. I watched a video and it took me less than 20 minutes to complete repair. Part fit perfect and I have already ordered another to keep as a spare.

YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!

remove 3 screws vent comes out put new part in works grate just like new a gain

I followed the very informative video and wrote down step-by-step notes for myself. The repair went very smoothly. The only thing I didn't realize, was that the dryer has 4 rollers, not just 2 shown in the video. All are easy to access once you disassemble. I had to do it twice since I had to order 2 more rollers in order to replace them all. Also, the triangle plastic washers come with the roller, so you won't need to order them separately like I did. I also changed the idler pulley roller while I was in there since that has bearings too. Just as easy. I'm very happy with my quiet dryer! One last note: The new rollers are a bit louder than normal at first, but they quiet down very quickly as you use the dryer. It must be because they are brand new.

remove top, front, drum, fan fan housing, replace motor