1106117733 Kenmore Dryer - Instructions

>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!

I used you-tube to troubleshoot and repair. Your part store was excellent to deal with. Delivery was prompt and cost was very reasonable. Thanks!

I googled the problem, then came across a site where somebody had experienced the same problem, and they changed the door catches to resolve it. I did a search for Whirlpool parts and found "partselect.com". I followed the instructions on the website and located the parts very easily and also discovered that there was a video on how to make this repair. We were tolerating this problem for quite some time and now the problem is resolved, thank you...

drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.

Replaced the cap over the door switch so when the door closed the switch was engaged

This was a classic easy repair and I am sure saved us bundles on a service call.

Reviewed the video showing how to remove the bad-order part and install the new part. No problem. Installing the new part was exactly what was shown in the video on the web page.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

I removed the plastic latch using a screw driver to pry it out. I had to use pliers to completely remove it. Then I snapped the new piece in. It worked perfectly the first time. Very easy repair.

i watched the video from Part Select. did exactly as seen and presto it was easily done. never could've done it without Part Select.

When I ordered the part, I viewed the installation video. That was a key step for me. It told me how to identify the correct part (there are multiple latch pieces in the repair kit, and one of them matches the type of door for the dryer), and how to disassemble the door to get the part installed. When the part came and I installed it, it turned out that I could snap the part in by hand, with no tools. It took about 5 seconds to try it, and it worked.

The dryer just stopped after a new load of clothes was put in. It appeared to be a power problem as there were not warnings, it just stopped. After checking the power, I suspected it was an electrical interlock problem. After nosing around, I traced the power to the dryer door interlock. Sure enough the switch was fine, but the mechanical lever was worn away. After Googling around for a replacement I found PartSelect.Com. Found the part, ordered it, and I am back in business. My wife is not happy though, as she wanted a new dryer:)

First I popped open the top of the dryer so I could see the part. I removed two screws from inside the door that hold the spring lever and switch together. I removed the spring lever which is also like a bracket that holds the switch in place. Put the spring lever back in place over the switch and reinserted the two screws. Done in about 10 minutes.

The dryer door has a switch hidden inside the machine housing. The switch has a lever that protrudes and when the door it closed it hits this lever allowing the dryer to activate.

*** Unplug machine ****

To replace: pulled out the lint trap, remove 2 screws under the lint trap. Pry the top open at the front (it's press fit in place and will pry open with a flat screwdriver).

Lift lid up and prop open (like the hood of a car). Find the switch at the front of the machine just above the drum. Remove 2 screws holding the switch in place (from just inside the drum area). Pull off the broken clip bracket, replace with new one and screw it back into place. Be careful not to drop the screws or bracket or they will fall into the bottom and you may never see them again. I can't stress this enough!!

Let the lid down and give it a good rap on the front to seat it back into place, replace the 2 screws under the lint trap. Replace the lint trap. And your done.