All Installation Instructions for Kenmore Dryer 11060052991

A hole in filter

Remove old filter
Vacuum out
Install new filter

Parts Used:

Lint Filter

Russ from Vernal, UT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

dryer would not turn on

turned off the power and removed the back cover, checked the thermal fuse had no continuity. ordered new part. very easy Installed the new thermal fuse,.replaced the cover, turned on the power and worked fine.

Parts Used:

Dryer Disposable Thermal Fuse

donald from MANVILLE, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

no heat

unplug the dryer used nut drive to take the back off unhook the hose from dryer . disconnect the wires. remove the 2 screws from thermal cut -off . install the new parts

Parts Used:

Thermal Cut-Off Kit

DAVID from DANVILLE, VA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

YouTube video dated 9/28/2015

How to repair E1 error/fault on Whirlpool Duet dryer model GEW9200LW0 please watch that video very helpful.

Parts Used:

Dryer Thermostat Internal bias

Madeline from PANA, IL
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set, Wrench (Adjustable), Wrench set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Intermittent squealing sound while dryer running

Take pictures along the way.
1. Remove lower front panel using screwdriver to lift up on tabs on top of panel.
2. remove door
3. unplug moisture sensor plugs
4. remove lint trap
5. on back of dryer, remove screws holding upper lid
6. slid up lid forward just a small amount, its hooked in towards the front of the upper lid. you will need to do this so you can can remove two screws under the lid holding the front panel of the dryer on
7. remove the front panel screws mentioned in step 6.
8. Remove lower front panel screws
9. remove front panel
10. reach into dryer at the bottom and release tension from belt pulley, sliding the belt off. (make a note of how the belt is routed around the drive and idler pulleys)
11. slide out tumbling drum
12. with drum removed, use socket wrench and socket to remove old idler pulley.
13. install new idler pulley
14. reinstall tumbling drum
15. slide belt back around tumbling drum, looping belt around drive pulley and around idler pulley.
16. When belt is installed, rotate drum a few revolutions to ensure belt rides correctly.
17. Reinstall front panel
18 slide top panel back into place and secure with screws from back
19. reinstall door
20. reattach moisture sensor plugs
21. reinstall lower panel

Parts Used:

Idler Pulley with Bracket

John from LAKE ZURICH, IL
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Dryer would shut off mid way through cycle and give an E1 error code

After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back together in reverse. I also took the time to clean any dust and lint out.

Parts Used:

Dryer Thermostat Internal bias

Dwayne from Bainbridge, PA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set

5 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Dryer was very loud and sounded like it was scraping

Took the back and top off of my front loader. I had checked on you tube for the problem and how to fix it and ordered the part. Just followed the directions on how to remove the old idle pulley and installing the new one. Dryer runs like new!

Parts Used:

Idler Pulley with Bracket

Annde from JEFFERSON CTY, TN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

not drying completely on the automatic settings

Not a handyman but this was an easy and cheap fix. Now the automatic settings are working and drying much faster. Unplug machine, front panel has 2 spring clips toward the edges that you stick a flat tool into and pull on the panel to open. Pull off the electrical connections from the old sensors by the right side of the lint screen. Needlenose pliers help with the one farther up there. Then just pull the old ones sensors out, stick the new ones in, reconnect the electrical and get ready to live the good life with dry clothes that don't smell musty.

Parts Used:

Moisture Sensor

Jason from Colorado Springs, CO
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Squeaky dryer

Ezee pezee lemon squeezee.

Parts Used:

Idler Pulley

robert from ELMA, WA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Dryer don't get hot !

It's a electric dryer, I knew it was related with the thermal !

Parts Used:

High Limit Thermostat

Thermal Cut-Off Kit

ENGEL from TRENTON, NJ
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Loud squealing when the dryer was running...especially on start up.

Simply followed the video that accompanied the part confirmation. Removed the top and front of the dryer. Removed the drum and belt. Unbolted (1 bolt) the Idler pulley and bracket and bolted on the new one. Reversed the sequence of disassembly and tried it out. The only minor difficulty was slipping the belt over the idler pulley after the drum was in place. This is where a second set of hands might be helpful to hold up the drum, while the other person puts the belt in place. Other than that, this was a simple repair and probably saved a couple hundred dollars for about 1.5 hours of my time. Thanks for the video...it was right on point, and made the job much easier.

Parts Used:

Idler Pulley with Bracket

Anthony from GROVELAND, IL
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

cold air vent in dryer was broken

remove 3 screws vent comes out put new part in works grate just like new a gain

Parts Used:

Outlet Screen Door Grille

Moisture Sensor

MIKE from WESTLAND, MI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Squealing when running

You tube and supplied video directions for the make and model. Follow step by step and the repair went easy. Worried when removing the dryer drum but it went smooth.

Parts Used:

Idler Pulley with Bracket

MICHAEL from Baden, PA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

dryer making noise. order parts

YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!

Parts Used: