1105072011 Kenmore Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Agitator would no longer move clothes during wash cycle
Removed the upper part of agitator from lower section by removing bolt with socket wrench and replacing inner "dog eared" gasket (cog) with the repair kit ordered here. It took some finagling and a rap with a rubber mallet but I got it installed and it works like a charm. Washer works like new with a $ 20.00 kit that was delivered fast, within 2-3 days! I highly recommend this site for easy instructions and excellent response time and pricing !
Parts Used:
-
Suzanne from Atkinson, NH
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
top half of aggitator wasnt engaging
slide ring at bottom of fabric softener receptacle up, remove the fabric softener dispenser . use a7/16" nut driver and loosen bolt in center of agitator remove old part checking the way it is located on all small parts. Configure new pcs according to opposite of removal put bolt back in and tighten agitator back down be sure to get it snug 10 to15 lbs. pressure .Next put fabric dispenser back slide lock ring back down . Check out operation!
Parts Used:
-
Leslie from New Waverly, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
The parts were worn but i think it still needs the top agitator
Took the fabric softener despencer off and center cap untightened the nut and pulled up on top agitator and put the new replacement parts back. It seems to be working good
Parts Used:
-
Donnie from Phelps, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Lid lock would not ingague.
Removed two brackets on back top of washer that hold top secure. Pulled top forward and up off off pins located on front top of washer. Located switch removed two screws holding it in. Then removed Panel on back of top in order to get to controls and unplugged other end of switch. Then reversed procedure and waher was back in service.
Parts Used:
-
Tom from Franklin, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
upper agatator not working
slipped up upper locking collar lifted off cover and removed 7/16 bolt that holds agitator in place. lifted out agitator and installed agitator repair kit. 123 simple. also next day delivery outstanding keep up good work
Parts Used:
-
Richard from Waverly, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Agitator stop rotating
Remove agitator cap remove screw then replace agitator. really simple to do approx 15 minutes.
Parts Used:
-
Rene from New York, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Washer needed new agitator
Took off old agitator, installed new agitator that was already assembled. Tightened nut and presto, installation was completed.
Parts Used:
-
Mary from Providence, RI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Wrench set
Was this instruction helpful to you?
Thank you for voting!
Auger would come completetly off when taking out clothes. The rubber washer had disintegrated.
I watched a Part Select video on replacing the augitator and just followed the directions to replace the thrust washer (which was showing wear) and the washer. The instructions that came with the thrust washer were helpful as well.
Parts Used:
-
Jennifer from Wake Village, TX
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!