11047561600 Kenmore Washer - Instructions

I basically just followed the directions in the Parts Select video. The only thing that was a little difficult was getting the new belt to feed onto the drum pulley, but after a couple of tries I was able to get it on. I'm glad the video mentioned this might be a little difficult or I might have thought I was doing something wrong.

Removed top and front lower panels remove door panel.Remove ring from boot seal don’t damage seal.Replace hose,reassemble.Job is a lot easier if you purchase tool to re-install door ring seal.Tool is available from several sites on the net.

I followed the video that accompanied the parts order confirmation. The replacement of the two parts, bellows and hose, were pretty straightforward. The job took a little less than an hour with little aggregation.

Only needed a pair of pliers for the clamps on the hoses connected to the pump. Removed the old pump ( no tools needed) and reinstalled the hoses. Works like a charm!

Watched the videos which were key! Thanks Parts Select! Replaced Bellows and dispenser hose. Cleaned all areas really well where new hose and bellows attached. Ran the washer in "clean washer mode" twice. Not a drop leaking. Thank you!

First unplug the washer and turn water off..Next take off back of the washer ( I used a socket set). Then underneath the front load tub, take that panel off to get to the pump (there are 3 screws in the front panel). Then get a towel put it underneath the water pump. Next take your pliers and squeeze the tab holding the end of the drain hose where it connects to the pump, Slide the clip up on the pump connection, pull off hose ,make sure your towel is underneath the end of the hose.Next reach your hand through the back of the washer and squeeze the plastic holder w[th your hand to release the hose. Then pull old hose out and replace it the the new hose. Just reverse the steps to put it in..

Replaced drain hose

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.

This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks

Followed the most helpful video.with some system differences. Had quite a bit of fitment challenge with the inner bellow sealing process...finally used dish soap to help 'stretch' the thing on.Works fine now thanks.

The removal of the bellows was easy and quick. The instructional video was really good. Only one problem with video. The step of removing the console from washer leaves out that there is a center screw in the center of console. I almost broke the console. It took took a long time in getting bellows on interior area due to tight finger space. Wire gasket fairly easy. The outer gasket after getting door and latch on. Whew! That was a bear. Video looked easy. I finally had to get help to get it on. The reason was that every time I thought I had it, the bellows would roll off will the wire gasket. A screw type as the inner area would make it so much easier. Shipping. Kudos to your company. I was expecting that I would be without washer for a week. I ordered on a Friday and it was here early Monday morning. That was amazing. By the way I did this except the outer wire gasket by myself. I finally had to get "husband" to help with that. Thanks Parts Select! If the need arises that I need another part. You will be my go to company.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Just follow the repair video and you are good to go. Very easy my 16yr old did it.

I watched the youtube video, then ordered the part from partselect. I then took my ipad out to the garage where I placed my washing machine and completed the removal of the old seal and installed the new one with ease. Be patient when you try and fit the new seal over the lip on the machines doorway. That was the only hard part. Once I got it started, the rest was easy. I am very happy the video was available and even easier to follow the link to order the part. Thanks! Presslerc