11044826300 Kenmore Washer - Instructions

I ordered the part, followed the instructions listed on appliance help and put it in... easy

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Could not have been easier. Have spent more time building kids' Star Wars Lego than this took...

I replaced the pump thinking this was the most likely cause of the problem. The pump is easy to access and get to. The reviews were helpful. The hose clamps were difficult to get back in place especially the one from the washer drain to the pump (need wide-jaw pliers). Now that I have seen the system work, the pump was not bad and the water from the drain still smells bad. I just ordered the filter 8181683, which looks like the only other thing that would prevent the water from draining completely. The drain hose is not blocked.

Looked at how the old drain pump was installed, then removed it and installed the new one. It was a fairly simple fix. The only feedback were that the parts picture was a little confusing becuase the picture didnt really look like the actual part, so we were unsure if we were ordering the correct part.

Washed three loads and it was ok but then it stopped draining again. I don't know what to do.

Pulled washer away from wall, unplugged power from outlet, shut off water valves and removed hosed from back of machine. Removed the 3 screws on the back top of washer that holds top on and removed top. Unplugged the 4 wires on the back of the valve, removed the screw that holds the valve in place, pulled the valve out so I could remove the hose clamp and hose from the valve. I then reversed the operation. It is really pretty simple.

First I want to acknowledge Parts Select for their prompt delivery(received parts in less than two days)and their unbeatable prices(approximately 1/3 less than two local appliance repair/parts shops). Repair was straight forward a simple swap of the pump and I saved quite a few dollars.Thanks Parts Select.Any future appliance parts needs will be purchased here.

Slid the washer out, took the hoses off and the back panel then the front panel, found coins in the filter tray and a baby bottle plastic cap was sealinhg the drain going into the plastic filter housing (it fits perfectly) removed all the items and put the white plastic screw cap back on the drain. Next problem was the washer walking around the laundry room, upon fixing the drain problem noticed the front shock absorber was unhooked and two on the right side of the machine had leak some grease, rehook the front shock and ordered two new ones it don't walk around anymore and works smooth and quiet now. I also have to add that Parts Select has been absolutely GREAT had the parts, delivered when promised.

We followed another very helpful repair story. Unplug machine. Unscrew top back screws, remove top of washer. Reach inside from the top in the front of the machine. Remove screws holding latch in place, unplug the three plugs attached to latch. Replace with new door latch, screw it in place, replug the three plugs, put top of machine back on, replace screws on back and your'e done! Works great! Job made easy thanks to others helpfulness!

My son pulled the washer out and found the parts that was leaking. He ordered the parts from your company. they arrived the next day and he re-pared the leaks and all is well.thank you

Removed the top of the washer by removing 3 screws on the back and sliding the top back and up. Removed the power cord and pipes. Next removed a screw holding the valve in place. Labeled the wires and pulled them off. The hard part was moving the locking tube ring further back on the tube before pulling the inlet tube off the valve. Reattach the black inlet tube and locking ring. I had to keep working it before it was in the right place. Some have mentioned that the hole didn't line up when they installed the valve. It turns out that there is a small slot in the plastic threaded tubes. One needs to wiggle the valve until the sheet metal rear wall fits in. Then the valve can be slid into position. Attach the mounting screw, hoses, top, power cord and try it out.

I removed the old pump and replaced it with the new one. I am the happiest person on earth right now to have my washing machine working at its best again. Thank you so much.

The replacemnt inlet valve was a little shorter than the original. I had to lenghten the slot on the back of the washer to get the mounting screw in the hole to attach the valve. There is only one mounting screw, so this was an important part of the replacement.

The washer tech manual stated to: 1) remove the top, 2) control console, 3) front below the door (front load washer), 4) remove the retaining wire, 5) pull back the rubber bellows, 6) remove the three screws and remove the door latch/lock assembly. I discovered that steps 1 through 3 are not required to replace the assembly. Installation is the reverse of steps 4 through 6. That was easy. The difficult part was figuring out how to reset the pressure switch so the drain pump would not start every time you reconnected to the power supply (pressure switch thinks the washer still contains water). With the power disconnected, I disconnected the pressure switch from the central control unit. Then I reconnected the power supply and pressure switch. That reset the pressure switch solved the problem with the drain pump. Washer works fine now.