11042926202 Kenmore Washer - Instructions

I purchased a new bellows from this site I followed their instructions. Just tricky getting the inner clamp on aligned and tightened.

Pull spring wire on front. Remove large hose lamp at tub. Reinstall in reverse order.

Repair was described as a simple 5 minute job following the enclosed directions. There were no directions included. Customer service replied they could not provide any instructions. I located a technical manual online and determined the steps necessary to replace the baffles. While some may just click them in, a proper repair requires the control pannel and machine housing to be removed. Then the tub assembly must be removed and the plastic tub separated from the basket. Three screws (one for each baffle must be installed. (I recommend using blue loctite to keep the screws from backing out). The entire process must then be reversed. This is a slightly complicated (note the pencil is to mark the locations of clips for ease of reinstallation. I am an Engineer and this process took over 2 hours and required a significant amount of space to lay out the parts as the machine was totally disassembled. This assembly is best accomplished with 2 people and an entire afternoon without interruption. It can be done by anyone with some mechanical skills, but find the consumer services technical manual first and be prepared to keep track of a lot of small and large parts. This is not the simple 5 minute job described by others (unless you just want to snap the baffles on the basket and not lock them down). In that case go ahead and order a few more sets as the clips will break and the baffles will slide off and you will be replacing them about every 6 months.

disconect wayer inlet hoses.remove screws that hold the top cover. This will expose the water inlet valve. remove the defective valve and any other associated clamps,hose etc. test run for leaks.

Removed covers per instruction video provided by website

We do not wish to have our repair published. The part itself was perfect and corrected our leaking problem but we did have difficulty with the installation despite detailed instructions. We appreciate a good price for the perfect part!

First took a picture and printed after disconnecting machine electric supply and removing top cover. removed screw holding vale in place, removed wiring .removed valve,attached wires to new valve inserted in place attached tubing and installed mounting screw and hoses, checked all again and tested

easy process: troubleshoot problem on website-- order part--get part--watch "how to replace"video on you tube-- get it done with only a screwdriver--go out for movie and dinner with $$ saved.

It was fast and pretty easy to do.

Remove top 3 screws.
Remove 1 screw that holds inlet valve.
slide valve to the right.
Mark and remove 4 connector wires.

Reverse order to install.

Replaced inlet valve. Took top cover off. Accessed inlet valve. Removed hoses. Replaced valve. Works like a charm.Corrected problem

Removed hot/cold water hoses from back of washer at water inlet valve. Pulled off top of washer by removing 3 screws at back of panel. Noted that water inlet valve had been damaged in move from storage. Pulled off 4 wires, 2 for hot and 2 for cold. Removed 1 screw holding inlet valve assembly to frame. Used pliers to release retainer ring on hose. Removed hose from valve outlet. Reversed process to install new valve.

The design of the baffle assembly must be a little off. Seems that the baffles must come loose at the screw and it tends to cause the attachment nubs to wear. The parts were delivered in no time, had the screws to replace the old screws (which was cool) all in all, the install went without a hitch. Plus, the site is great, easy to identify parts and the order process is a piece of cake. Maybe your folks could come over and redesign our parts site!

turned off water valves , disconnected and placed hoses into small bucket . removed top . I then removed screw off old valve , shimmied it out of the hole , removed hose with pliers , slipped off white set of plugs and then black set .. Then I put hose on new valve , placed plugs ( black & white ones ) be sure to mark the correct side .. for me two white were on the right side of valve and black on left side .. placed valve back into its respective spot . attached the screw .. note I sled mine to the right just a bit and all lined up perfectly . Attached hoses , ran test cycle on warm , cold , hot .. All hoses were hooked up correctly and leak free . put lid back on and perfect .. The hardest part , was moving the shelves above my washer , really was super simple . Watch the video twice. You will be able to do it in no time. Saved me 245$ . From my appliance shop the part 150.$ 100 service call and the install fee $ since the install was so easy couldn't be much but .. Its a guesstimate ..You can do it !

My hubby and I replaced the part in about 20 minutes, including moving the washing machine. We love doing household projects like this. We're a great team and putting in this part showed how good we work together. Thanks for the quick response too!