11042836200 Kenmore Washer - Instructions

The design of the baffle assembly must be a little off. Seems that the baffles must come loose at the screw and it tends to cause the attachment nubs to wear. The parts were delivered in no time, had the screws to replace the old screws (which was cool) all in all, the install went without a hitch. Plus, the site is great, easy to identify parts and the order process is a piece of cake. Maybe your folks could come over and redesign our parts site!

turned off water valves , disconnected and placed hoses into small bucket . removed top . I then removed screw off old valve , shimmied it out of the hole , removed hose with pliers , slipped off white set of plugs and then black set .. Then I put hose on new valve , placed plugs ( black & white ones ) be sure to mark the correct side .. for me two white were on the right side of valve and black on left side .. placed valve back into its respective spot . attached the screw .. note I sled mine to the right just a bit and all lined up perfectly . Attached hoses , ran test cycle on warm , cold , hot .. All hoses were hooked up correctly and leak free . put lid back on and perfect .. The hardest part , was moving the shelves above my washer , really was super simple . Watch the video twice. You will be able to do it in no time. Saved me 245$ . From my appliance shop the part 150.$ 100 service call and the install fee $ since the install was so easy couldn't be much but .. Its a guesstimate ..You can do it !

When I looked at the website for latch repair they showed a video (can't remember which brand but not Amana) where you had to take off the top and front of the washer to get at the latch part on the washer. For the Amana I had, you simply had to pull out a portion of the rubber gasket held onto the washer by a wire/spring combination (you can take the wire off) to get at the latch assembly. You could then undo the three screws holding the latch to the washer, pull it out and unplug the three wiring connections to remove the old latch. Then plug connections into the new latch, reinstall, tighten screws and fit gasket and wire/spring assembly back together. Much easier than going thru the top and front of the washer!

Need to elongate the hole in the frame to allow the screw that holds the valve in place to be inserted. You could not even start it as is. Also it put pressure on the valve so it would not seat properly. Need to include in the instructions you may need to elongate this opening in order to complete this repair. Other than that is was extremely easy. Parts fit well. Video instructions were great. Other than not knowing about the valve screw placement changing both pieces were extremely easy. Washing machine was repaired within minutes and is functioning properly again. Even the diagnosis tool was excellent as I have no experience with repairing washing machines but your site helped me trouble shoot the issue, order the parts (and receive in a couple of days) and replace the defective pieces in minutes. Changing these 2 items got me up and running an days and cost significantly less than what a repairmen would have charged just to show up at the door. Appreciate all your help!

Shut water off to washer, unhook hoses, removed back panel of washer, removed screw that holds the valve in place then unhooked the water line that connects to the washer and removed part. Place new inlet valve in position and hooked hoses and mounted it in place, put back panel back on and hooked hoses up and turned water on. Did a test wash and it worked

REMOVE HOSES AND POWER PLUG REATTACH EVERYTHING AND THEN DONE.

Shut off the hot water supply (pretty sharp eh?). Disconnected the hose from the hw supply and the at the connection to the washing machine. These had not been touched in at least 15 years and were somewhat tough to loosen but finally came ..... accessibility was a problem for the connection to the water supply as it was in a recessed wall box. Fortunately, we had some washers for the hose connections so the install was a snap. Hardest part of the whole job was moving the washing machine out from between the drier and the wash tub .... tight fit. Thanks for the quick service and to FED EX for their delivery. The delivery fellow was a real gentleman.

snapped in place

so easy!!three screws to take top off,one screw held valve in take hose off then install new part and reverse take apart order and done!!!Would have been sick if had to pay service call for such a easy fix!! Mike

Unplug machine,remove three screws that hold on top cover.
Unplug latch switch assembly,then open front door of washing machine, remove three screws which hold latch
switch. Install in reverse order.

I ordered the part, followed the instructions listed on appliance help and put it in... easy

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

We followed another very helpful repair story. Unplug machine. Unscrew top back screws, remove top of washer. Reach inside from the top in the front of the machine. Remove screws holding latch in place, unplug the three plugs attached to latch. Replace with new door latch, screw it in place, replug the three plugs, put top of machine back on, replace screws on back and your'e done! Works great! Job made easy thanks to others helpfulness!

Removed the top of the washer by removing 3 screws on the back and sliding the top back and up. Removed the power cord and pipes. Next removed a screw holding the valve in place. Labeled the wires and pulled them off. The hard part was moving the locking tube ring further back on the tube before pulling the inlet tube off the valve. Reattach the black inlet tube and locking ring. I had to keep working it before it was in the right place. Some have mentioned that the hole didn't line up when they installed the valve. It turns out that there is a small slot in the plastic threaded tubes. One needs to wiggle the valve until the sheet metal rear wall fits in. Then the valve can be slid into position. Attach the mounting screw, hoses, top, power cord and try it out.

I removed the old pump and replaced it with the new one. I am the happiest person on earth right now to have my washing machine working at its best again. Thank you so much.