11042834201 Kenmore Washer - Instructions

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I ordered the part, followed the instructions listed on appliance help and put it in... easy

I just take out the botton part and fine what part what i need chage and just chage exactly like the old if yoo dot remember all the wires please take pictures and you hava guia to check went you are finished

The difficult part was getting the water from the washer without making a huge mess. I used a shop vac loosened the cover on the filter/strainer assembly use the shop vac to suck up the water before spills all over. if the tub is full I dumped my shop vac twice total. 1 Remove pedestal drawer 2 removed lower cover to expose mechanicals and pump assembly 3 vac out the water by using above procedure. 4 rotate hose clamps to a position where you can get the needle vice grip on them/remove hose clamps. 5 lift cover exposing electrical connections on the pump assembly depress tab slide connector out. 6 remove 1 torx head screw securing pump to base of washer. 7 remove pump assembly. 8 Reinstall in reverse of above instruction. I also took the lower tub hose off and washed, bleached along with hot water to. clean it

removed top cover,disconnected wires to valve,removed valve and hooked up a washer hose to test valve,one side was leaking,valve would not close.replaced with new valve that I received in 2 days,do not buy after market.

I saw a u tube video and followed the presenters instructions. Very simple instruction very simple repair. The whirlpool duet is a well designed machine with the mechanical parts easily accessible. I know if if would have had a professional service come and repair if it would have cost several hundred dollars. It cost me the parts, $50. 00 (That was for the 3-pack of baffles), 1 beer and my time. "Easy fix".

I followed the guy on the video. The only parts that were tough was having the right tools and having enough space to put the new part in. The part was only 70 dollars and I was so proud that I could do it. I am not very handy so if I can do it then anyone can. Plus I saved some money!

(1) Turn off water valves (2) remove water lines (3) remove three metric star screws from top/back of washer (4) remove to plate (5) remove single screw retaining water inlet valve at back of washer (6) remove electrical connections from water inlet valve and flow meter (7) loosen hose clamps at back of soap dispenser (8) remove assembly/apply new parts (9) reverse above directions. Because the plastic nipple at the back of the soap dispenser was brittle, it partially broke on me. I applied urethane glue to the break and let it dry overnight. Next day I applied marine-grade silicone sealant around the break area. That evening I assembled and then used the washer to test for leaks. Success!

most would have thrown out the appliance ,but at $1000.00 to replace it was worth the shot to repair ,basket was under warranty (450.00 value )part damaged was the outer plastic being damaged ,washer repaired for under 150.00 and back inservice saved 850.00

Could not have been easier. Have spent more time building kids' Star Wars Lego than this took...

I replaced the pump thinking this was the most likely cause of the problem. The pump is easy to access and get to. The reviews were helpful. The hose clamps were difficult to get back in place especially the one from the washer drain to the pump (need wide-jaw pliers). Now that I have seen the system work, the pump was not bad and the water from the drain still smells bad. I just ordered the filter 8181683, which looks like the only other thing that would prevent the water from draining completely. The drain hose is not blocked.

Looked at how the old drain pump was installed, then removed it and installed the new one. It was a fairly simple fix. The only feedback were that the parts picture was a little confusing becuase the picture didnt really look like the actual part, so we were unsure if we were ordering the correct part.

Washed three loads and it was ok but then it stopped draining again. I don't know what to do.

Pulled washer away from wall, unplugged power from outlet, shut off water valves and removed hosed from back of machine. Removed the 3 screws on the back top of washer that holds top on and removed top. Unplugged the 4 wires on the back of the valve, removed the screw that holds the valve in place, pulled the valve out so I could remove the hose clamp and hose from the valve. I then reversed the operation. It is really pretty simple.

First I want to acknowledge Parts Select for their prompt delivery(received parts in less than two days)and their unbeatable prices(approximately 1/3 less than two local appliance repair/parts shops). Repair was straight forward a simple swap of the pump and I saved quite a few dollars.Thanks Parts Select.Any future appliance parts needs will be purchased here.