All Installation Instructions for Kenmore Washer 11027032601

F1 code show

Removed/ Replaced. Machine control motor

Parts Used:

Electronic Machine and Motor Control Board

Bernard from OCOEE, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

The agitator was making grinding noises

Removed the softener dispenser and cap that's under it. Used 7/17" socket with an 18" long extension to reach the bolt that holds agitator down. Pulled auger off, pulled lower agitator off. Removed the 6 philips head screws that hold basket hub in place. Removed hub and installed new one, replaced screws. Lightly greased spline and reinstalled lower agitator. The auger has the cam section in it. A trick to get the rollers in place is to secure them to the cam with rubber band. Have string tied to the band. Insert the cam and when almose all the way in, pull rubber band off and the rollers stay in place. Reinstalled the bolt, cap and softener dispenser.

Parts Used:

Basket Hub Kit

Mark from Erie, PA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Old hot water inlet hose had budge at both ends.

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

Parts Used:

Inlet Hose - 5 FT

Jimmy from MEMPHIS, TN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

the drain pump leaked water

fairly simple remove and put back in …I watched a video of a similar Maytag pump replace got some tips…the electoral connection is shielded by a pull up tab…so it was quite simple I got extra hose clamps in case?…didn’t need them

Parts Used:

Drain Pump

Hose

James F Meehan from COARSEGOLD, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The seal in the upper agitator cap broke

I just unscrewed the top agitator cap and slid the o-ring on and put it back. Done in seconds.

Parts Used:

Washer Inner Cap Seal

Veronica L from Junction City, KS
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Both outside door handles turned very beige

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Parts Used:

Spray Paint - 12 oz. - White

Howard from Boynton Beach, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

23 of 74 people found this instruction helpful.

Was this instruction helpful to you?

Water would not drain

I read the directions on this web site and was able to install the new drainage pump in about 30 minutes. I suprised myself. Thanks.

Parts Used:

Drain Pump

Neil from Onalaska, WI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench set

Was this instruction helpful to you?

f1, code on the face plate of the washer,we kept on resetting it

we ordered a motor controller,pop out the old one,then replaced it with the one we ordered,and bingo,problem is solved

Parts Used:

Electronic Machine and Motor Control Board

Delinda M from Chicago, IL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

Was this instruction helpful to you?

did not work

reemplace the lid lock assembly

Parts Used:

Washer Lid Lock Assembly

JESUS from PORT ARTHUR, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Hole in casing of drain pump due to loose nickle being pulled into pump - No screen in inlet to pump

Pulled back off of washer. Removed Spring clamps from inlet and outlet of pump housing. Removed hoses. Removed three screws holding pump in place. Disconnected electrical plug connector. Reassembled in reverse order. Note: new pump had no isolators and pump motor cover looked like a rat had chewed it up; however, motor, pump, and hoses appeared to be new. Put it on without the motor cover and it works. Epoxied the old pump housing to seal it up and now have a spare.

Parts Used:

Drain Pump

CARROLL from HENDERSONVILLE, NC
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

Was this instruction helpful to you?

washing machine showed F50 code

I watched a video on how to do it.it wasn't very difficult the hardest part was getting the machine out of the laundry room and laying it over

Parts Used:

Rotor Position Switch Kit

david from knoxville, TN
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Socket set

Was this instruction helpful to you?

UL flashes, will not spin, really loud,& black spots under washer

We ordered the outer tub & bearing and now the washer works like it was brand new.

Parts Used:

Outer Tub Assembly

Elijah from Point Hope, AK
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Socket set, Wrench (Adjustable)

Was this instruction helpful to you?

Shake and moved

At the time that I received the order part, Me and my Wife and 15 years old Douther got on it. We removed the very top of the counter and replaced once at the time every supension rod cleaned nice and neat. then we put the top on it's place conected the water hoses pluged it in and it was ready to roll.

Parts Used: