11026432503 Kenmore Washer - Instructions

The reason it took as long as it did was because the job is not in line as the work I normally do.
It would be a fairly easy job for an experienced repairman. (Taking the back off the washer was time consuming for me) The rest of the job was easy as the part was a perfect fit.
I remember having a problem blending hot/cold water for some time. Most recently, while washing a load the water did not want to shut off. I can't remember how I diagnosed the water not shuting off as a problem along with the water temp control, but it is now repaired.
With the new valve installed, water temp select is now OK and the water now shuts off as normal.

Removed the clips. Pulled out the old pump. After trying to get the new pump on the shaft of the motor, I realized that some corrosion had built up on the motor shaft. I got a small tack hammer and very lightly tapped the shaft to remove the corrosion. The pump then slid on the shaft with no problem. Replaced clips. Job complete.
The corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.

After taking the entire washer apart one time, we learned that we could take the top and front of the machine off only to repair it. I found Part-select online and with the model number locating the part was easy. It arrived within 3 days and with instructions I could easily replace the old part with a few tools. I spent dollars instead of hundreds for a new machine.

I repaired my Kenmore washing machine replacing the clutch, Motor coupling and cogs. All of the parts came quickly and with good instructions. Best of all there were links to youtube repair walkthroughs. With out these step by step instructions this project would have taken much longer. Now the washer is like new! WATCH THE YOUTUBE PAUSE DO THE STEP AND REPEAT

Removed capscrew in end of agitator shaft took cover off machine-[ unscrewed two screws holding down control panel, hinged back, pryed retaining clips out, rocked back machine cover.]
Removed motor mounting clips and pump hoses, swinging motor and pump out of the way. Removed 3 capscrews holding transmission, pulled transmission towards me removing agitator shaft, disassembled clutch assembly - removing one cirlip then another, installed new clucth parts in same order

Unplug power from wall.
Disconnected water lines
Tip Unit on it's side. (Recommend turning so motor is to the top side)
Disconnect Electrical connector and Hoses from the pump and motor.
Disconnect metal straps used to retain the motor to the transmission. (screwdriver to pry)
Remove old coupling pieces from transmission/motor(used a long screw driver, rock back and forth)
used air compressor to clean up electric motor
replace new coupling on motor and transmisison (may need hammer to tap into place)
set rubber bushing on transmission side (transmission shaft should be facing up at this point)
replace electric motor into place, making sure to line up bushing and motor mounts.
replace metal strap connectors between transmission / motor (this can be tricky, as the one in the back is hard to get at.)
replace electrical connectors and hoses
connect washing machine power and water and test

flip machine back remove two spring clamps and hoses remove two spring clamps and water pump save $500.+on a new washer

First I removed the softener bin by pulling it up and off, then I removed the plastic seal by pulling it up and out, then I removed the 1/2 inch bolt with a ratchet and extension, then I removed the upper and lower agitator assembly from the machine and seperated the two by putting my feet on the lower agitator to hold it to the floor and pulling the upper agitator fast and firmly.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.

This is a relatively new washer and failed early. My previous whirlpool washer lasted 20 years without any repairs. 1. First inquired about the spin problem in partselect. Machine will not sping unless manualy forced then it will take off but weak. 2. Partselect suggested a clutch problem. Ordered the part that came fast. When I tried removing the shaft hub with a hammer and chisel it will not get loose so I opted ordering the special wrench to loosen the tub hub. 3. I put the machine on its back and loosened the pump retaining clips. Do not remove the hoses from the pump. Move the pump away from the motor shaft. Remove the motor electrical connector and set aside. 4. Remove the three bolts holding the gearbox-motor assemply and pull it out of the tub. 5. Put the assembly on a towelwith shaft up and remove the separator washer from the old clutch that is sitting on the gearbox. Then remove the c-retaining clip from the shaft. 6. Pry out the wire retaining clip from the clutch and pull the old clutch out of the shaft. 7. The clutch kit I ordered came with a plastic brake to clutch cam so I replaced it too, just remove the retainig clip from the brake that is at the bottom of the tub and replaced the part. 8. Installed the new clutch and the retaining clips in reverse order. Replace all parts that came with the kit. The new clutch spring was already in place. 9. Put the assembly back into the tub and re-install all the other items in the same order. It spins good now! 10. While replacing parts, methodically clean all the lint from the motor and from under the machine. The gearbox showed signs of leaking oil so its a question of cost. I left it there until it fails then I'll buy a new machine.

Replaced AGITATOR DIRECTIONAL COGS (4) looking instruction video . Replaced CLUTCH LINING KIT following video of this site "WASHER REPAIR-REPLACING THE CLUTCH ASSEMBLY". Replaced SEAL, GEARCASE COVER and NEUTRAL DRIVE ASSEMBLY as follow: 1)CLUTCH Assembly and motor removed, took the GEARCASE on a bench vise to hold in place and the long shaft up side. You can get help from other person to hold secured in place instead a vise.2)Following a youtube video I tested gearcase with a reversible drill using DIRECT DRIVE MOTOR COUPLING PART next To transmission side instead of electrical motor. Drill turning counter clockwise drive the long shaft oscillating (it agitate via agitator cogs). Drill turning clockwise run the exterior sleeved part around shaft (upper side of metal gear inside gearcase and fixed on top to clutch to get washer spin). My experience was didn't rotate so we had to take apart gearcase cover.3)Unscrewed and removed gearcase cover. Cover was sticked by old seal gasket so a screwdriver helped me to remove it.4)Cleaned joint removing old gasket.5)Repeating drill test I realized big nylon gear did'nt rotated and removed uppercut clip with pin pliers with care for not lose the pin. Removed the next washer, the plastic gear and found a plastic part with a tooth broken. This part is with NEUTRAL DRAIN ASSEMBLY so replaced assembly following part instructions. I recommend take pictures in order to reassemling and use ALLEN WRENCH 5/32'' inches.6)Fill up to half of gearcase with 16 ounces (about 1/2 of case) of gear oil supplied by PARTSELECT or automotive gear oil SAE 85w90 or SAE 90.7)Replaced SEAL, GEARCASE COVER. HARD TO REMOVED AND REPLACE! Take care not break!. I had to use a piece of metal tube and a vise.8)Applied automotrice black seal gasket silicone around the cover joint and case.9) Replaced the cover and reversal instruction video.THANKS to this site I get excellent service and Enjoyed with my toy.

Completely dismantled washer per video , replaced gasket and spanner nut, then re-assembled washer. I’m a 58 year old female. It was tough. Main issue was that video was for dif. Model washer. Had to figure out some things myself.

While taking apart my washing machine to clean the plastic basket I discovered the 3 main seals down the agitator were completely disintegrated and water was leaking onto the motor and onto the floor. The seals are a tight fit but slide into place easily with lubrication. When putting everything back together a bit of lubrication will be necessary as well. The leak is gone and my nearly 30 year old washer is working as well as the day it came off of the assembly line.

I followed the online instructions to remove the shell and attempted to remove the drum, but not having the special wrench to remove the special nut, tried using a screwdriver and hammer, which failed to loosen the nut. I then started examining the the undercarriage and saw that I could replace the springs without removing the tub and did that. In the course of replacing the springs I discovered I could also access the wear pads by lifting the drum off of the undercarriage and placing a block to hold it above the pads. I was able to pop the old pads out by tapping underneath them with a hammer. The new pads were then installed and the weight of the drum popped them in. It was necessary to lift the drum assembly three times for each of the three pads.

After removing the bolt (7/16" head), and using a pair of pliers to remove the 3-4 in deep "cup", it was immediately obvious how to assemble the new cup and pawls (ratchets).

Orienting the black "bearing" was not so obvious, but on closer inspection of the illustration, it became clear. The four "ears" of the bearing go closest to the pawls. The little tabs that are co-planar to the ears fit into the four grooves of the new cup.

And here's the trick (besides making REALLY, REALLY SURE how the pawls orient)--Soak the black bearing piece in hot water to soften it up, and let it slide over the cup better. If you don't, you risk breaking it. If you do, it slides over and "clicjs" into place, with the ears resting right against the bottom lip of the cup, capturing the pawls.

Installation back into the washer is obvious.

The thing works like a charm! It hasn't worked this well for a decade!

Actually, my brother-in-law did the repair. He replaced the part, but found out that it was another part that was the problem. We kept the part because he told us that this part would be the next thing to go, so we just kept it. Now, we ordered and fixed the correct part and it works great.