11022994103 Kenmore Washer - Instructions

Hello the installation was real simple I first uplug machine from wall I turn off all water leading to in to the machine I then tip machine on it side I then took loose all wiring leading to the motor then motor is held up with 3 screws and 2 bands that hold it in place I reinstall the new motor coupling insert the wires and turn back on the water leading to machine then plug machine back in, every thing was good to go. . . . Save a lot of money doing it my self so simple to do. . . .

Inserted new drain hose thru back and snapped into place. Tipped washing machine back, clamped new hose with pliers.

Washer was not agitating. My husband did not have a clue what to look for, but he took it apart and noticed two of the four directional cogs were stripped. Did an internet search and found the part on your website and thought we would give it a try since the part/shipping was under $20. The parts came in three days and my washer lives on. Was ready to get a new one since it is 18 years old, but I will not wait. Excellent website with all instructions and parts breakdown of the washer.

Just watched the video. Take from a 63 year old. Who never fixed a washer. Thx a lot for the video it saved me a lot of money being on a fix income. and it was less than $ 10 that was included shipping.

Removed Softner dispenser and cap. With a 3/8" socket wrench and extension And 7/16" socket I took out the screw holding the agitator and removed top section of agitator. Turned upside down and removed the rubber grommet that holds the cogs in place. Replaced cogs and reinstalled grommet. Aligned top part of agitator with 2 tabs and put back in place and secured with 7/16" screw. Replaced cap And dispenser. Good to go. Works perfectly. Very easy repair.

Half inch extension. Removed plastic set piece. Remove agitator cap. Remove ring remove worn cogs. Replaced new cogs Replace lock ring, back together. 10 minutes

Removed broken hose and replaced with new hose. My washer will be 21 years old in January.

Just changed out the old pump with the new one. It went very quick and smooth!

I went to Youtube, looked up motor coupling repair for a Kenmore/Whirlpool washer. Chris Fix had an easy to follow video. I tilted the machine back, propped it up. Removed four clips holding two parts in place. Replaced the faulty coupler, Set the engine back in place replaced the clips, and was finished for a total price of $18.

After flipping the washer on it's side snap off the clips that hold the motor in place and discard the old coupling. The new coupling fits in very snug some may need a little persuation to attach but once attached the motor lines up nicely and just snap back the clips, turn the washer over and test with a fresh load.

First I removed the old hose to ensure I ordered the correct part. When I got home from work the part had arrived by us mail. I opened the box and installed it without any modifications and within 5 mins. I hooked up the washing machine to the hot and cold water, then the drain hose. I was washing cloths within 20 mins of opening the box!

Removed top cap of agitator and pulled out the inner cap. Spread a pair of needle nose pliers and placed them in square holes on each side of nylon fitting. Unscrewed nylon fitting and removed top half of agitator. Replaced directional cogs/dog ears and put agitater back together. Works like new. Easy fix.

PS Received parts in 72 hours. $10.00 bucks and never left the house.

It was easy, take off the cap, then loosen the nut. Take it apart, change the dog ears, put back together. It was done.

1. Need mop, bucket to catch leftover water in machine before you remove old hose. 2. Removed old hose by removing clamp. 3. Dried up any remaining water around fixture before attaching new hose. 4. Slide clamp to bottom of hose before attaching to machine. 5. Attached hose and clamp to machine where old hose was removed from. Make sure clamp is secure. (Please note that clamp that came with the new hose was too big. I used the old one. Worked perfectly). 6. Finally run a little water in you washer, then run out to test tightness and there is no leaks.

Removing top console control panel, deataching 2 clips and removiong the entire box to get access to the agitator and the direct drive, one part on the top and other on the bottom of the washer,removing top cap of the spinner got access to the agitator. Using 1/2" socked and pliers remove & rep[lace the agitator. for the direct coupling: remove the water pump (2 clips) 1/4" socked & screw driver remove the electrical Motor, remove & replace the direct coupling, put all removed parts back toguether, reasembly the box ataching clips on place, console panel Install, perform operational check, was good I have the washer running like a new machine.