11022994101 Kenmore Washer - Instructions

First I screamed at the ceiling, because I have a three year old and an infant, and the washing machine was dead. Then I went to youtube. It seemed like the "agitator dogs" were the issue.

In this spirit of any repair, I replaced them, and it was not the issue. I don't know what I expected.

Ceiling. YouTube. Pacing.

Then I figured it was this part - the motor coupling. I unplugged the machine and took out the drain tube. I leaned the machine back and propped it up with an empty detergent bottle, because those were abundant. Ratchet off a few bolts and the motor comes out. The coupling was indeed broken. The new one slips right in - I tapped it a few times with a mallet for good measure / vengeance. Ratcheted the bolts back on and tipped it back up.

Pros: Washer works now.
Cons: Everest-esque laundry pile to address.

But hey, it worked! I am no handyman and it wasn't too bad at all. Half hour tops.

Disconnect power & water then drain hoses.
We flipped the washer on it's side to gain access to the bottom. There was no need to take off the back panel. Keep a 5 gallon bucket and a few rags handy for the extra water in the pump line.
Disconnected the wiring harness. Removed the brackets holding the motor. It's a little tight on the back bracket. It has a 1/4" hex nut on the back side, so I used a 1/4" drive socket (see: small). Removed the bolts holding the gear case (this makes it a lot easier). Disconnected the pump hose and rotated the motor & gear box and pulled forward. This gives you access to the coupling. Remove the broken part. Clean the area for debris. NOTE: each part of the coupling has 3 fingers (these are what breaks off), so check to make sure you get all broken parts. Insert the new coupling. It has 3 parts; the plastic fittings go on tight and need to be snug to the shaft. Use a screwdriver handle on the center and tap down with a small hammer. Spray silicone on the rubber coupler to allow a little better slide.
Reverse the process. Line the gear box and motor up and push back into the tub assembly. We used 2 people to do this. It's easier to have someone stand over it and hold / rotate the gear box while the other one can align the motor & bolt everything back on.
It took us an hour, however, if you were doing a couple you could get it down to 30 min. flat.
Go wash your clothes!

I followed the provided video for changing the centerpost gasket.

I successfully completed the repair. I will say that I had challenges at almost every step. Getting the inner basket off the centerpost was difficult, as was rocking the outer tub upward from the base.

If a man is somewhat handy, this is a doable repair. Be patient and take your time. The video is very helpful and I don't think I could've done the repair without it. It's a pleasure to watch an expert like Steve.

It's gratifying to successfully repair a major appliance such as a washing machine and I look forward to many more years of reliable service from this well-built appliance.

Disassembled lower part found nothing wrong.
Started disassembly from the top. Immediately ran into trouble not knowing exactly how the tub was anchored to the drive. Once I got down to the tube and drive block there was nothing I could do to go further. I guessed it was a press fit onto the drive, but there were many instructions and I couldn't be sure. Parts Select expanded drawing was the most useful tool; it was correct omitting a few details. Anyhow, cleaning out my garage I found one of my old gear pullers that I could ring to complete the disassembly. All the sudden I was in business, pulling the washer drum off the drive block and shaft, getting down to the leaky lower seal. A that point it was just a matter of cleaning everything up and buying all the rusted out parts to reassemble. I spent $150-200 on parts, but its completely rebuilt now and runs like a charm. Probably have around 20-50 hours all told, into the repair. Most of this was reading instructions, watching videos, and trying to figure out the rest (3). Doing the actual work spread over time until my wife and sons threatened to throw the thing out. Never. Once I decide I'm gonna do something, I do it. LOL!

slid the old seal off the lid and the new one popped on so easily
I do so many self- repairs at home now this was not even an issue.

I followed the online instructions and found it remarkably easy. I saved a lot of money and will certainly use PartSelect in the future! Washer works like new again!

leaned washer back on wall at or more than 45degree undid two screws off of motor. pulled old part off put new on reinstalled motor Done

I ordered the new cogs but didn't want to wait the few days for them to arrive. So I decided to try and temporarily repair the old ones. After looking at the picture of the new ones on this site I realized that the teeth were just worn down. I took all four of them out and used a grinding disc to carve the teeth down deeper. They were not perfect. (I would recommend holding the teeth with a vise.) However, after reinstalling the cogs the machine worked perfect and that was two weeks ago. I'm not going to install the new ones until I have to.

Watch the video

Found leveling spring loose on bottom of washer, the sheet metal on bottom of cabinet ad rusted through. Drilled new hole in sheet metal and installed new leveling spring. Greased hole with blue marine grease so it will last another 40 years.

Looked at the repair instructions on your web site and it made the repairs simple and easy.

Tipped the washer onto it's side, used pliers to loosen clamps on old hose. Removed outer drain hose from white plastic hose adapter on back of washer. Removed white hose adapter (snaps out of place) and old hose. Fed new hose through opening for white adapter, then snapped new adapter into place on back of machine. Put the new hose in place and replaced clamps. Sat washer back upright. No more leaking! It was easy and didn't take more than 15-20 minutes.

After moving washer and UN-Plugging electrical. 1. Remove the 2 screws that hold the Control Panel to the lower chassis. 2. Lift the Control Panel up and forward to expose the water level switch. 3. Remove the dial. 4. Remove the old switch, (a plastic tab locks it into the panel, try to release it(from the front) with a small screwdriver, (mine broke off, releasing the switch). 5. Remove the electrical connection by lifting the connection locking tab. 6. Remove the air tube. 7. BLOW into the air tube to ensure it is not blocked. 8 . Reconnect the air tube and electrical connection. 9. Carefully install the new switch into place, turning it to line up and lock the tab into the panel. 10. Re-install the dial and return the Control Panel screws into the lower chassis. NOTE: If the included air hose needs to be replaced, the time and difficulty needed to make repairs will increase.

I had given up on repairing the machine and placed order for a $650 washer. After returning to home from this shoping, I wanted to know possible problems with the current machine and came across a story on your web site attached to the Coupling parts description. It described the repair details. Encouraged I placed order for this $15 parts and repaired in an hour, saved the replacement machine cost. Thanks a lot

We unscrewed the two screws at the back of the control panel. Holding the control panel on both ends
we pulled it toward the front of the machine, slightly and gently lifting it at the same time, removing it from the metal surround. Holding the control panel up off of the surround we rocked the surround forward and lifted it off the washing machine frame.
We could see where the leak was coming from. We took the hose clamps from the two ports, then
using a pair of pliers pulled the two clips that are holding the pump onto the shaft protruding from the
electric motor. We matched up the part on the web sight. Ordered the part then when it came in we just reversed the order putting the machine back together. The hardest and most time consuming
thing about this repair was the clean up of the washing machine. (Dirt and soap residue does
build up on the inside of the wash tubs.)