11022832102 Kenmore Washer - Instructions

The water pump had a small leak when washing clothes, and my wife was nagging me about it. I know men, youwere shocked that I said nagging and wife in the same sentence. Me being a man, I would have just left it since it is in the laundry room in the carport.

I turned the washer on its side and felt where the leak was on the pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.

I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!

unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.

Removed cap, used a wrench to remove nut for agitator, put new one in place put nut back on and the cap back on and started washing clothes easy fix saved me $300.00 Thank you

Disconnected old power cord inside control cabinet, removed strain relief , then removed damaged power cord. Reinstalled new cord with new strain relief.

I had to unscrew 2 screws that held the control panel, then remove the 2 end caps, remove 2 screws that held the control panel to the washing machine. I then lifted the control panel and leaned the lower case forward. All this to get access to the ground screw for the lid mount. It sounds like a lot, but actually it was quite simple. I replaced the old switch with a new one and put everything back together just like new. No extra screws or parts that I could not remember where they came from. Thanks Parts Select. Reading the comments from others helped me to realize that I could do the work without worry. The only problem I had was ordering the correct part. That did not happen until I got the correct part number from the old part.

Removed end caps on control panel, removed two screws, lifted the control panel and rolled it back out of the way.
Undid clips and wire connection and pulled the cabinet off. Replaced the switch and put everything back together.
Easy job but helps to have two people to get the cabinet back on right.

Removed the screws holding the control panel onto the washer. Removed the switch knob and then the switch (required unlocking a tab and then rotating the switch to remove). Unplugged the wiring connector and the water sensing tube. Replaced the switch in the reverse order and remounted the control panel. Test run proved the washer was working again.

but switch fixed

Purchased lid trigger elsewhere but got the connector on line here after being told I would need to purchase complete wiring harness to correct. Once lid trigger was in i stripped the three wires that went to lid trigger and pushed thru the back side of the connector. Then I plugged into trigger. Now washer works again. Very easy to do.

Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job

I unplugged the machine.
Removed the back panel.
Located the switch, removing it and then following the wire to the plug, unplugging it.
replaced with new switch, plugged it in and replaced the back panel.
Removing and putting the back panel back was the hardest part.

I looked for a youtube video on how to repair the lid switch. The video was very good but was filmed in a perfect world. My washer sits in a somewhat confined area so getting the outside skin put back perfectly was a bit tricky.

Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.

Removed old tube and replaced with new version. Replacement slightly different than original since the new part included a feature that appears to prevent the problem. New part still fit and is operating well so far.

first remove your washer cabinet from unit. Next on your back left bottom is where your new spring goes. In my case my spring was broke making the washer spin out of balance. Repair with your new spring, and install cabinet back place plug it in and wash a load of cloths. Wow what a difference!!!! job took about 20 minutes. Very Happy