11020112311 Kenmore Washer - Instructions

I watched the PartsSelect video. I was hoping for the tub with the slots in the tub mounts, but mine didn't have them, so I had to lay it down on its back. The only thing I did that was not in the video was I placed a 2" thick closed cell foam knee pad I had on hand between the tub and the back of the housing. When I laid it down, the tub was elevated by 2". This made reaching the two rear rods a little easy. It seems that there would be a more robust way to achieve the dampening affect, but I guess this is cost effective.

It's strange that I searched for my issue several times and only saw recommendations to level the washer. It was level. Then one day I ran across the suspension rod resolution. It didn't do it on every load, but after a year of my wife nagging me and threatening to get a new washer, I finally fixed it. The biggest issue is just logistics in a condo hallway and a little leaking water. I also replaced my hoses. Should be in good shape until the next thing.....

Used your exploded view of the area to determine the problem-found the broken part and reassembled following the drawing. I felt like a pro after a test and kept my wife happy. [only lost a few days waiting for the parts which arrived as expected]

I followed the instructions provided by the video which I thought were spot on. Even to the size of the phillips screw driver.

W10721967 Splutch Cam Kit

Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.

When I took off the 13mm nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.

Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.

Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.

Tightened up the pulley as the video showed me that might be the issue.

Replaced the suspension rods not an easy task but very rewarding to hear it running quiet again when spinning.

Unplugged the washer turned off the water disconnected the water lines then took the cover off and disconnected the wires and took 2 screws out and took the old part out and put the new 1 in

First, this is the second time the transmission actuator went bad. The first-time washer was still under warrenty and I watched the tech replace it. This time warranty has expired and I'm mechanically inclined, so I ordered the part. Replacing was easy, unplug, tip washer up so you can get under it, remove plastic guard (two hex nuts) and remove actuator by removing two screws. Reverse procedure to install new actuator. The only caution I will say is when tipping washer if you have a wall to lean it against, perfect, just put something under it for saftey so it can't fall on you.

Watch video on the site and the insulation will be easy and take about 30 min.

Removed the old and replaced with new

Followed detailed instructions which were supplied with the parts. It was easy and my machine is working great with no issues. Also I just didn’t get the main drive pulley, all new parts came for the bottom end, great service and excellent parts.

used the Parts.com video. I am not mechanical at all, but removed the old part and installed the new part without a hitch. Very happy.

I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!

Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!

Unplugged, removed cold and hot lines, moved out to garage, unscrewed 3 screws on the back, lifted up the top, removed and replaced 1 suspension rod at a time with washer leaning against wall sideways, easy peasy didn’t take no time at all, moved it back in 3 screws back in place hot and cold screwed back in and walla! It worked and has been working flawlesssly..