11020097993 Kenmore Washer - Instructions

Yes, I agree that the actual replacement of the pump was an easy task on this whirlpool washing machine, however, unlike other posters, I had no access through the bottom of the machine. My machine has a solid pan on the bottom. It has a large hole in the center - I think to access the transmission, but no access where the pump is.
So, I had to dismantle the entire enclosure, first the back (about 6 screws, a couple of electrical connections, etc.), then remove the rest of the enclosure to reveal the guts of the machine. I also had to disconnect a small vacuum tube attached to the tub, and remove the control console on top along with the back. It was pretty straight forward, took about two hours to dismantle. Then, the actual removal of the pump was as easy as others have described here - two spring clips and a hose clamp and I had it in my hand. I ordered the new part, which came very quickly - 2 days I think. Then I took another two hours to re-assemble the machine. It works - yeah!
Symptoms - water leak on the floor, it was actually intermittent for a time, so I procrastinated. Then when I actually did the work, I could see the rust trail and follow it to the leaky pump. The pump was actually leaking through the center, where the drive shaft from the motor goes. There is probably a seal between the impeller and the central drive slot that gives out after a while.
New pump in - machine back together - no leaks.

I followed the online instructions and found it remarkably easy. I saved a lot of money and will certainly use PartSelect in the future! Washer works like new again!

Found leveling spring loose on bottom of washer, the sheet metal on bottom of cabinet ad rusted through. Drilled new hole in sheet metal and installed new leveling spring. Greased hole with blue marine grease so it will last another 40 years.

Looked at the repair instructions on your web site and it made the repairs simple and easy.

leaned washer back on wall at or more than 45degree undid two screws off of motor. pulled old part off put new on reinstalled motor Done

I ordered the new cogs but didn't want to wait the few days for them to arrive. So I decided to try and temporarily repair the old ones. After looking at the picture of the new ones on this site I realized that the teeth were just worn down. I took all four of them out and used a grinding disc to carve the teeth down deeper. They were not perfect. (I would recommend holding the teeth with a vise.) However, after reinstalling the cogs the machine worked perfect and that was two weeks ago. I'm not going to install the new ones until I have to.

I loosened two screws which held the knob panel in place. I undid the two clips holding the cabinet and removed it. The pump has two clips holding it on, I removed those and the pump came free. Taking advice from these forums, I did not remove the hoses attached. I disconnected the wiring harnesses from the motor. The motor has 2 clips also, these being held on with screws. I removed the screws and the clips. THE MOTOR IS HEAVY.
You will see the coupling on the "spindle" of the motor. In my case, both plastic pieces were cracked in 2 places. I removed the old coupling and cleaned the "spindles" and lightly regreased.
The replacement pieces I ordered were the "improved" ones with the metal insert. They were a tight fit on the motor but I used a socket and hammer. (lightly). Line up the coupling pieces, reattach clips, DONT FORGET THOSE SCREWS HOLDING THE MOTOR CLIPS. Pump goes on next, etc. MAKE SURE ALL WIRING IS RECONNECTED! Cabinet goes back on, large clips holding cabinet to rear of machine go back on. Knob console flipped down and reattached.
Plugged it in and I was good to go! This washer is almost ten years old and this is the second time I have been able to bring it back from the dead, the first time being the agitator "dogs" wearing out. THANKS PARTSELECT!

slid the old seal off the lid and the new one popped on so easily
I do so many self- repairs at home now this was not even an issue.

Started taking machine apart, would of been easier if I had looked at the online diagrams first, but dismantled enough to find a few broken parts, I could not tell the coupling was broke till I actually removed the water pump and motor. Total cost for 3 plastic parts was less than $25 including shipping. Received parts in 3 days on standard lowest cost shipping. Put machine back together, with just a few extra screws and wire clips, but machine works like new now. Much better than the cost of new or used washer.

I had no idea what the problem was...other than the drum would not spin and it made a horrible noise...so I figured the motor was still good. I figured the repair man would charge me $200 and a new washer is $300...so what have I got to lose? First, I unplugged the unit. I started by removing the top control box by removing two screws in the back of it. Once off, there are two big clips which hold the body in place. That came off easy. I removed the back next and now had everything out in the open. I disconnected the exit greywater pump which was easy with two snaps. I tipped the unit on the side and removed the motor - also attached with two snap on clips. Between the motor and the gearbox there is a shock absorbing coupler which consist of two white plastic rings with 3 fingers each. These interconnect with a black rubber piece. Once of the white rings was cracked in half and one of the fingers was broken off. So that easy to figure out. I ordered a new coupling on partselect on Friday afternoon. On the next morning, Saturday, Fedex showed up with the replacement part. I was pretty amazed at the fast service since I only paid $7 for ground shipping. Anyway, I put the new coupling on and put the whole thing back together...we've run a dozen loads since without a hiccup. Beats dumpstering the unit or calling a repairman. I spent about an hour to take it apart and about an hour to get it all back together. You definately need a good socket set, screwdrivers. Good luck.

I actually didn't remove any of the panels. I tipped the washer at a 45 degree angle to the back and side to release the motor clamps, unhooked the power to the motor and removed the two drain pipes from the motor.

Once I had all of that removed, I was able to pull the motor away from the transmission and put the new coupling pieces on. The hardest part was holding the motor up (it is fairly heavy and cumbersome to hold while the machine is tipped like that). The pieces didn't go on too easily either. It would have been ideal to have at least the front panel off to use a hammer more easily. I did manage to get it on using a socket and a hammer. With some light taps it went on.

Next I put the hoses back on, the power, the bottom motor clamp, and then wrestled for another 30 minutes getting the top motor clamp on.

The clamps are the metal like springs that hook into the transmission and then spring tighten the motor to the transmission. Then there is a little screw that holds it in place... Not easy to see from any angle, and that is where having the front panel off would be ideal.

I've NEVER worked on a washer before and I accomplished this by myself in about 2 hours. I think if you are sure this is the problem, fix it yourself. Best 20 bucks and 2 hours I spent this month by saving a couple hundred on a new washer or repair person.

Removing top console control panel, deataching 2 clips and removiong the entire box to get access to the agitator and the direct drive, one part on the top and other on the bottom of the washer,removing top cap of the spinner got access to the agitator. Using 1/2" socked and pliers remove & rep[lace the agitator. for the direct coupling: remove the water pump (2 clips) 1/4" socked & screw driver remove the electrical Motor, remove & replace the direct coupling, put all removed parts back toguether, reasembly the box ataching clips on place, console panel Install, perform operational check, was good I have the washer running like a new machine.

There are 4 tabs that come from the main agitator body through the center & lock into the centerpiece that holds the directional cogs. They have a tab similar to a cable tie that can only be put on once. They need to be clipped before it will dissassemble & reassembly is difficult because they need to be timed to reattach the round center cog plate. Maybe cut off 2 of them & taper the other 2 them for easier reassembly.

After flipping the washer on it's side snap off the clips that hold the motor in place and discard the old coupling. The new coupling fits in very snug some may need a little persuation to attach but once attached the motor lines up nicely and just snap back the clips, turn the washer over and test with a fresh load.

Thank you for asking me how it went. the washer would not spin or pump water out, so I put it on its side and saw that the coupling was bad.
so I found you on the internet, thankyou very much, and put a order in for the part. well waiting for the part, I took the old coupling out it was easy, there was two metal bands one on each side of the motor took them off two bolts holding a plate on, and had old coupling in hand. and it was easy to put back with the new coupling. I enjoyed working on it. Dennis