11020096991 Kenmore Washer - Instructions

I did a Google search for the model number and found this site, PartSelect.com. Based on the diagrams on the site and what I could see underneath the washer, it was clear that the motor coupling was now gone and the shattered pieces of it were all over the floor. So I ordered a new coupling and waited for it to arrive, it was shipped in just a few days. Once I had the new coupling all I had to do was remove a couple of brackets holding the pump onto the motor, and the motor onto the gearbox; unplug the electrical terminals and lift the motor out. There are two halves to the coupling, one sits on the shaft of the gearbox and the other on the shaft of the motor. Both of these are seated into a rubber boot that is also a part of the coupling. Once the motor is sitting on the gearbox with all the coupling parts seated in place, just plug everything back in and replace the brackets. You will need a 1/4 socket to remove/replace the motor brackets. Also, it should be noted that you will want to unhook everything that is hooked to the wall (hoses, power cord) but it assumed you've already done this if you have access the the underneath of the washer.

I removed the cover for the softener dispenser on the top of the agitator. Then reached in and removed the cover of the nut and washer which was very sticky and sealed with an o-ring. This took a bit of pressure. Then used a socket wrench with an extension to loosen the bolt and took the whole agitator out of the machine. Then I set the agitator on the floor and with a fine 12 inch long screw driver released the catches while turning and pulling the agitatior with my other hand and holding the lower agitatior on the floor with my feet. I then turned the upper part over and removed the cogs and holding mechanism.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.

Put new one on work good, but now can't pump no more .the problem now is the spin cycal broke and I not going to fix it. Thank for the part work good.

I always tought that I could never fix my own washer with so little time and with less than $25 dollars so good that our washer is working like new once again thanks to partselect. . . . I will be happy to buy from you any time.

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

Took out old parts and put in news ones, super easy and works great!!

Too simple. The old one practicaly fell off and all I had to do was push the new one into place. It locked itself in and was ready to use.

No more rattling or noise when it runs now.

Looked at the repair instructions on your web site and it made the repairs simple and easy.

I ordered the new cogs but didn't want to wait the few days for them to arrive. So I decided to try and temporarily repair the old ones. After looking at the picture of the new ones on this site I realized that the teeth were just worn down. I took all four of them out and used a grinding disc to carve the teeth down deeper. They were not perfect. (I would recommend holding the teeth with a vise.) However, after reinstalling the cogs the machine worked perfect and that was two weeks ago. I'm not going to install the new ones until I have to.

I loosened two screws which held the knob panel in place. I undid the two clips holding the cabinet and removed it. The pump has two clips holding it on, I removed those and the pump came free. Taking advice from these forums, I did not remove the hoses attached. I disconnected the wiring harnesses from the motor. The motor has 2 clips also, these being held on with screws. I removed the screws and the clips. THE MOTOR IS HEAVY.
You will see the coupling on the "spindle" of the motor. In my case, both plastic pieces were cracked in 2 places. I removed the old coupling and cleaned the "spindles" and lightly regreased.
The replacement pieces I ordered were the "improved" ones with the metal insert. They were a tight fit on the motor but I used a socket and hammer. (lightly). Line up the coupling pieces, reattach clips, DONT FORGET THOSE SCREWS HOLDING THE MOTOR CLIPS. Pump goes on next, etc. MAKE SURE ALL WIRING IS RECONNECTED! Cabinet goes back on, large clips holding cabinet to rear of machine go back on. Knob console flipped down and reattached.
Plugged it in and I was good to go! This washer is almost ten years old and this is the second time I have been able to bring it back from the dead, the first time being the agitator "dogs" wearing out. THANKS PARTSELECT!

We had to take the motor out and remove the coupling, when putting it back together we had some problems because the washer was on its side and the lid was open. After putting the motor and coupling back together we tried to turn it on, unknowing to us the lid was open so nothing would happen, finally we realized the lid was open. The actual repair was not complicated, just human error made it seem than way

leaned washer back on wall at or more than 45degree undid two screws off of motor. pulled old part off put new on reinstalled motor Done

I had given up on repairing the machine and placed order for a $650 washer. After returning to home from this shoping, I wanted to know possible problems with the current machine and came across a story on your web site attached to the Coupling parts description. It described the repair details. Encouraged I placed order for this $15 parts and repaired in an hour, saved the replacement machine cost. Thanks a lot

removed water lines from back of washer. tilted washer to get access to the pump/ removed 2 hoses at pump and removed to snap clips attaching the pump. easiest repair i ever did. washer works fine now.

Yes, I agree that the actual replacement of the pump was an easy task on this whirlpool washing machine, however, unlike other posters, I had no access through the bottom of the machine. My machine has a solid pan on the bottom. It has a large hole in the center - I think to access the transmission, but no access where the pump is.
So, I had to dismantle the entire enclosure, first the back (about 6 screws, a couple of electrical connections, etc.), then remove the rest of the enclosure to reveal the guts of the machine. I also had to disconnect a small vacuum tube attached to the tub, and remove the control console on top along with the back. It was pretty straight forward, took about two hours to dismantle. Then, the actual removal of the pump was as easy as others have described here - two spring clips and a hose clamp and I had it in my hand. I ordered the new part, which came very quickly - 2 days I think. Then I took another two hours to re-assemble the machine. It works - yeah!
Symptoms - water leak on the floor, it was actually intermittent for a time, so I procrastinated. Then when I actually did the work, I could see the rust trail and follow it to the leaky pump. The pump was actually leaking through the center, where the drive shaft from the motor goes. There is probably a seal between the impeller and the central drive slot that gives out after a while.
New pump in - machine back together - no leaks.